6509-E Switch>sh mod Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAD103700DV 2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL10403BWM 3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL10403B4T 5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAD104006KR 6 0 Supervisor-Other Unknown Unknown Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 0019.2f1c.4920 to 0019.2f1c.494f 2.4 12.2(14r)S5 12.2(18)SXF6 Ok 2 0019.55c4.b500 to 0019.55c4.b52f 2.5 12.2(14r)S5 12.2(18)SXF6 Ok 3 0019.2fc7.fbe0 to 0019.2fc7.fc0f 2.5 12.2(14r)S5 12.2(18)SXF6 PwrDown 5 0011.9202.88e8 to 0011.9202.88eb 5.2 8.4(2) 12.2(18)SXF6 Ok 6 0000.0000.0000 to 0000.0000.0000 0.0 Unknown Unknown Unknown Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Centralized Forwarding Card WS-F6700-CFC SAL1035ZLZ2 3.0 Ok 2 Centralized Forwarding Card WS-F6700-CFC SAL1035ZM45 3.0 Ok 3 Centralized Forwarding Card WS-F6700-CFC SAL1034ZDJ7 3.0 PwrDown 5 Policy Feature Card 3 WS-F6K-PFC3B SAD103705HM 2.3 Ok 5 MSFC3 Daughterboard WS-SUP720 SAD104007DG 2.5 Ok 6 Policy Feature Card 3 WS-F6K-PFC3B SAD1040046D 2.3 Other Jun 7 20:43:20.854 EDT: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (not supported) Jun 7 20:43:27.897 EDT: %STANDBY-6-STATECHANGE: Vlan80 Group 1 state Standby -> Active Jun 7 20:43:27.945 EDT: %STANDBY-6-STATECHANGE: Vlan276 Group 1 state Standby -> Active Jun 7 20:43:28.641 EDT: %STANDBY-6-STATECHANGE: Vlan280 Group 1 state Standby -> Active Jun 7 20:43:29.161 EDT: %STANDBY-6-STATECHANGE: Vlan1376 Group 1 state Standby -> Active Jun 7 20:43:30.181 EDT: %STANDBY-6-STATECHANGE: Vlan312 Group 1 state Standby -> Active Jun 7 20:43:30.873 EDT: %BGP-5-ADJCHANGE: neighbor 25.x.y.1 Down BGP Notification sent Jun 7 20:43:30.873 EDT: %BGP-3-NOTIFICATION: sent to neighbor 25.x.y.1 4/0 (hold time expired) 0 bytes Jun 7 20:43:32.265 EDT: %STANDBY-6-STATECHANGE: Vlan1376 Group 1 state Active -> Speak Jun 7 20:43:32.833 EDT: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure Jun 7 20:43:32.833 EDT: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (FRU-power failed) Jun 7 20:43:42.269 EDT: %STANDBY-6-STATECHANGE: Vlan1376 Group 1 state Standby -> Active Jun 7 20:43:55.705 EDT: %OSPF-5-ADJCHG: Process 1, Nbr 25.x.y.19 on Vlan1213 from FULL to DOWN, Neighbor Down: Dead timer expired Jun 7 20:44:11.673 EDT: %EARL-SP-4-EBUS_SEQ_ERROR: Out of Sync error. Errorcode 0x1500102 Jun 7 20:44:12.273 EDT: %EARL-SP-4-EBUS_SEQ_ERROR: Out of Sync error. Errorcode 0x1500102 Jun 7 20:44:15.205 EDT: %BGP-5-ADJCHANGE: neighbor 25.x.y.2 Down BGP Notification sent Jun 7 20:44:15.205 EDT: %BGP-3-NOTIFICATION: sent to neighbor 25.x.y.2 4/0 (hold time expired) 0 bytes Jun 7 20:44:17.729 EDT: %OSPF-5-ADJCHG: Process 1, Nbr 25.x.y.2 on Port-channel99.1211 from LOADING to FULL, Loading Done Jun 7 20:44:45.897 EDT: %BGP-5-ADJCHANGE: neighbor 25.x.y.2 Up Jun 7 20:45:12.101 EDT: %CONST_DIAG-SP-STDBY-3-HM_TEST_FAIL: Module 6 TestSPRPInbandPing consecutive failure count:7 Jun 7 20:45:12.101 EDT: %CONST_DIAG-SP-STDBY-6-HM_TEST_INFO: CPU util(5sec): SP=5% RP=0% Traffic=0% netint_thr_active[0], Tx_Rate[21], Rx_Rate[0], dev=1[IPv4, fail=7] Jun 7 20:46:10.817 EDT: %BGP-5-ADJCHANGE: neighbor 25.x.y.1 Up Jun 7 20:47:12.557 EDT: %CONST_DIAG-SP-STDBY-3-HM_TEST_FAIL: Module 6 TestSPRPInbandPing consecutive failure count:14 Jun 7 20:47:12.557 EDT: %CONST_DIAG-SP-STDBY-6-HM_TEST_INFO: CPU util(5sec): SP=3% RP=0% Traffic=0% netint_thr_active[0], Tx_Rate[0], Rx_Rate[0], dev=1[IPv4, fail=14] Jun 7 20:47:33.757 EDT: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode Jun 7 20:47:37.729 EDT: %OSPF-5-ADJCHG: Process 1, Nbr 25.x.y.1 on Port-channel98.1210 from LOADING to FULL, Loading Done Jun 7 20:49:54.633 EDT: %PFREDUN-SP-6-ACTIVE: Standby initializing for SSO mode Jun 7 20:49:54.825 EDT: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output. Jun 7 20:49:56.161 EDT: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup configuration to the standby Router. Jun 7 20:50:27.056 EDT: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 6. Jun 7 20:50:27.160 EDT: %FABRIC-SP-5-FABRIC_MODULE_BACKUP: The Switch Fabric Module in slot 6 became standby Jun 7 20:50:52.363 EDT: %ONLINE-SP-6-INITFAIL: Module 6: Failed to synchronize Port asic Jun 7 20:50:52.363 EDT: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled (OIR slot disable) Jun 7 20:50:53.231 EDT: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode Jun 7 20:53:08.364 EDT: %PFREDUN-SP-6-ACTIVE: Standby initializing for SSO mode Jun 7 20:53:08.560 EDT: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output. Jun 7 20:53:10.268 EDT: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup configuration to the standby Router. Jun 7 20:53:41.168 EDT: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 6. Jun 7 20:54:06.504 EDT: %ONLINE-SP-6-INITFAIL: Module 6: Failed to synchronize Port asic Jun 7 20:54:06.504 EDT: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled (OIR slot disable) Jun 7 20:54:07.484 EDT: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode