Rommon reg: 0xE2004180
##########Unknown backplane 5

k2diags version 4.2.2_h

prod: WS-X4013+TS  part: 73-9337-11  serial: JAE1053JSHE


Power-on-self-test for Module 1:  WS-X4013+TS
 Port/Test Status: (. = Pass, F = Fail, U = Untested)
 Reset Reason: Software/User 


Port Traffic: L2 Serdes Loopback ...
 0: .  1: .  2: .  3: .  4: .  5: .  6: .  7: .  8: .  9: . 10: . 11: . 
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 


Port Traffic: L2 Asic Loopback ...
 0: .  1: .  2: .  3: .  4: .  5: .  6: .  7: .  8: .  9: . 10: . 11: . 
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 


Port Traffic: L3 Asic Loopback ...
 0: .  1: .  2: .  3: .  4: .  5: .  6: .  7: .  8: .  9: . 10: . 11: . 
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 


Switch Subsystem Memory ...
 1: .  2: .  3: .  4: .  5: .  6: .  7: .  8: .  9: . 10: . 11: . 12: . 
13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: . 
25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: . 
37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: . 
49: . 50: . 51: . 52: . 53: . 54: . 55: . 


Front Panel 10/100/1000 Ports ...
 1: .  2: .  3: .  4: .  5: .  6: .  7: .  8: .  9: . 10: . 11: . 12: . 


Front Panel SFP Ports ...
13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 


Module 1 Passed


Exiting to ios...

Rommon reg: 0xE2000180
###################################
              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EWA10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 11-Jul-07 00:08 by dchih
Image text-base: 0x10000000, data-base: 0x114BC038


####### ######  ######  ####### ######    ###
#       #     # #     # #     # #     #   ###
#       #     # #     # #     # #     #   ###
#####   ######  ######  #     # ######     # 
#       #   #   #   #   #     # #   #        
#       #    #  #    #  #     # #    #    ###
####### #     # #     # ####### #     #   ###

Unsupported chassis type 65535, system can not boot
Rebooting in 10 seconds...
10  09  08  07  06  05  04  03  02  01 





 
 ********************************************************** 
 *                                                        * 
 * Welcome to Rom Monitor for WS-X4013+TS System.           * 
 * Copyright (c) 1999-2004 by Cisco Systems, Inc.         * 
 * All rights reserved.                                   * 
 *                                                        * 
 **********************************************************
 
 Rom Monitor Program Version 12.2(20r)EW1 
 Supervisor: WS-X4013+TS  Chassis: Unknown( 5 ) 
 Hardware Revisions - Board: 7.4 CPLD: 4 Dagobah: 226 
 

 MAC Address  : 00-16-46-c1-f2-8c 
 IP Address   : 10.1.1.113 
 Netmask      : 255.255.255.0 
 Gateway      : Not set. 
 TftpServer   : Not set. 
 Main Memory  : 256 MBytes



 ***** The system will autoboot in 5 seconds *****


 Type control-C to prevent autobooting.
 . .
 Established physical link 100MB Full Duplex
 Network layer connectivity may take a few seconds
 . . .

 ******** The system will autoboot now ********


 config-register = 0x102 
 Autobooting using BOOT variable specified file.....

 Could not find a valid file in BOOT environment variable. 
 BOOT variable can be set from IOS. To find currently set
 Rom Monitor variables, please type 'set' command.

 For help on choosing a boot method,  type 'confreg' command.
rommon 1 >