Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

AAA + RADIUS on Catalyst Switchs

The command "switch(config) radius-server ... " doesn´t appear on my catalyst 3500. The version of Catalyst IOS is c3500xl-c3h2s-mz.120.5.WC5

How I can define the RADIUS Server Ip address and port!?

Regards

1 ACCEPTED SOLUTION

Accepted Solutions

Re: AAA + RADIUS on Catalyst Switchs

I think I have the same version. As you can see below, the command is there.

#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C3500xl Software (C3500xl-C3H2S-M), Version 12.0(5)WC5, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Tue 28-May-02 11:41 by devgoyal

Image text-base: 0x00003000, data-base: 0x0034A3C8

ROM: Bootstrap program is C3500xl boot loader

uptime is 40 weeks, 15 hours, 35 minutes

System returned to ROM by reload

System restarted at 23:17:01 MET-DST Mon Aug 19 2002

System image file is "flash:c3500xl-c3h2s-mz.120-5.WC5.bin"

cisco WS-C3524-XL (PowerPC403) processor (revision 0x01) with 8192K/1024K bytes

of memory.

Processor board ID FAB0513V068, with hardware revision 0x00

Last reset from warm-reset

Processor is running Enterprise Edition Software

Cluster command switch capable

Cluster member switch capable

24 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:05:9B:93:13:80

Motherboard assembly number: 73-3904-11

Power supply part number: 34-0851-02

Motherboard serial number: FAB051240RK

Power supply serial number: PHI050204Z8

Model revision number: A0

Model number: WS-C3524-XL-EN

System serial number: FAB0513V068

Configuration register is 0xF

#conf t

Enter configuration commands, one per line. End with CNTL/Z.

(config)#rad

(config)#radius-server ?

attribute Customize selected radius attributes

challenge-noecho Data echoing to screen is disabled during Access-Challenge

configure-nas Attempt to upload static routes and IP pools at startup

deadtime Time to stop using a server that doesn't respond

directed-request Allow user to specify radius server to use with `@server'

host Specify a RADIUS server

key encryption key shared with the radius servers

optional-passwords The first RADIUS request can be made without requesting a password

retransmit Specify the number of retries to active server

timeout Time to wait for a RADIUS server to reply

vsa Vendor specific attribute configuration

Hope this helps you out

Leo

6 REPLIES

Re: AAA + RADIUS on Catalyst Switchs

I think I have the same version. As you can see below, the command is there.

#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C3500xl Software (C3500xl-C3H2S-M), Version 12.0(5)WC5, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Tue 28-May-02 11:41 by devgoyal

Image text-base: 0x00003000, data-base: 0x0034A3C8

ROM: Bootstrap program is C3500xl boot loader

uptime is 40 weeks, 15 hours, 35 minutes

System returned to ROM by reload

System restarted at 23:17:01 MET-DST Mon Aug 19 2002

System image file is "flash:c3500xl-c3h2s-mz.120-5.WC5.bin"

cisco WS-C3524-XL (PowerPC403) processor (revision 0x01) with 8192K/1024K bytes

of memory.

Processor board ID FAB0513V068, with hardware revision 0x00

Last reset from warm-reset

Processor is running Enterprise Edition Software

Cluster command switch capable

Cluster member switch capable

24 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:05:9B:93:13:80

Motherboard assembly number: 73-3904-11

Power supply part number: 34-0851-02

Motherboard serial number: FAB051240RK

Power supply serial number: PHI050204Z8

Model revision number: A0

Model number: WS-C3524-XL-EN

System serial number: FAB0513V068

Configuration register is 0xF

#conf t

Enter configuration commands, one per line. End with CNTL/Z.

(config)#rad

(config)#radius-server ?

attribute Customize selected radius attributes

challenge-noecho Data echoing to screen is disabled during Access-Challenge

configure-nas Attempt to upload static routes and IP pools at startup

deadtime Time to stop using a server that doesn't respond

directed-request Allow user to specify radius server to use with `@server'

host Specify a RADIUS server

key encryption key shared with the radius servers

optional-passwords The first RADIUS request can be made without requesting a password

retransmit Specify the number of retries to active server

timeout Time to wait for a RADIUS server to reply

vsa Vendor specific attribute configuration

Hope this helps you out

Leo

New Member

Re: AAA + RADIUS on Catalyst Switchs

Thanks Leo for you attention!

Very strange. See below my sh version. Is realy the same version:

"switch#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C3500xl Software (C3500xl-C3H2S-M), Version 12.0(5)WC5, RELEASE SOFTWAR

E (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Tue 28-May-02 11:41 by devgoyal

Image text-base: 0x00003000, data-base: 0x0034A3C8

ROM: Bootstrap program is C3500xl boot loader

switch uptime is 44 minutes

System returned to ROM by power-on

System image file is "flash:/c3500xl-c3h2s-mz.120-5.WC5.bin"

cisco WS-C3512-XL (PowerPC403) processor (revision 0x01) with 8192K/1024K bytes

of memory.

Processor board ID FAB0514U061, with hardware revision 0x00

Last reset from power-on

Processor is running Enterprise Edition Software

Cluster command switch capable

Cluster member switch capable

12 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:04:9B:52:28:80

Motherboard assembly number: 73-4100-09

Power supply part number: 34-0851-02

Motherboard serial number: FAB051111CH

Power supply serial number: PHI050204F8

Model revision number: A0

Model number: WS-C3512-XL-EN

System serial number: FAB0514U061

Configuration register is 0xF"

You can see below that the command still doesn´t appear:

"switch#

switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.

switch(config)#r?

rmon

switch(config)#radius-server?

% Unrecognized command"

switch(config)#

Do you have any idea of what´s happening!?

Thanks!

Re: AAA + RADIUS on Catalyst Switchs

Not really an idea. Did you configure IP on int vlan 1and is AAA configured?

Otherwise, you have a 3512, mine is a 3524. Got it? It is hard to imagine but you never know with Cisco.

Goodluck,

Leo

New Member

Re: AAA + RADIUS on Catalyst Switchs

Ok. Thanks Leo,

Now is working!

Thanks for your attention!

Regards!

New Member

Re: AAA + RADIUS on Catalyst Switchs

I had to do the following -

Config t

aaa new-model

end

copy run start

then the radius-server command appeared as expected.

New Member

Re: AAA + RADIUS on Catalyst Switchs

Same happened to me with c3500XL-c3h2s-mz.120-5.WC3b.

no "copy run start", reloading etc...

I had to pass to c3500xl-c3h2s-mz.120-5.WC8

1228
Views
0
Helpful
6
Replies