Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco ISE 1.1 On ESXi 5.0

Hello Everyone,

I have a very unusual issue with my installation of ISE on my VMWare ESXi 5.0 environment. I am not sure if anyone else has seen this error but whenever I issue the command "show application statuse ise" I get the following output;

ISE Database listener is running, PID: 13675

ISE Database is running, number of processes: 27

ISE Application Server is running, PID: 15163

ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory

ISE M&T Session Database is not running.

ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory

ISE M&T Log Collector is running, PID: 15379

ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory

ISE M&T Log Processor is running, PID: 15457

ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory

ISE M&T Alert Process is running, PID: 15296

Not sure if this could be an issue with the use of VMWare ESXi 5.0 and not 4.1 or if something else is going on.

Thanks in Advance

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
New Member

Cisco ISE 1.1 On ESXi 5.0

Offically ISE only support 4.x Vmware. So I would say its the 5.0.

also try "application reset-config ise" ... if it doesn't fixes it then it is definitely 5.0

6 REPLIES
New Member

Cisco ISE 1.1 On ESXi 5.0

Offically ISE only support 4.x Vmware. So I would say its the 5.0.

also try "application reset-config ise" ... if it doesn't fixes it then it is definitely 5.0

New Member

Cisco ISE 1.1 On ESXi 5.0

Looks like that didn't work with resetting the config of the ISE. I will revert back to ESXi 4.1 and give it a shot.

Thank you very much. I will mark this thread as answered.

Thanks

New Member

Cisco ISE 1.1 On ESXi 5.0

Just wanted to throw a little update out there. After reverting to version ESXi 4.1 I would recieve the same error and also noticed i would get this error as soon as the mode of ISE would be set to Licensed.

It also indicates that it was successfully installed. Could this also be a corrupt ISO file?

Because after running "show application status ise" i still see those multiple errors about the *.jar file/directory not being found.

And again after using the "application reset-config ise" i get the following

Thanks

Cisco ISE 1.1 On ESXi 5.0

I have ISE 1.1 running in labs, and limited pilot's on ESX5 with no issue, i don't think it's related to that.

New Member

Cisco ISE 1.1 On ESXi 5.0

Gian, after you reported that you had the same issue with 4.x I installed 1.1 on ESX5 without any problem and then installed in of vmware fusion without any problem.

How much disk space was allocated in your installation?

New Member

Cisco ISE 1.1 On ESXi 5.0

I got it working fine after re-downloading the .iso file. The file i downloaded previously might've been corrupt. But it is working for me now. Not sure how to close the thread but again i was successful by just re-downloading the installation file.

Thanks to all who responded.

1924
Views
0
Helpful
6
Replies