Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
tbg
New Member

ISE NFR VMWare - Default username and password

Hi,

i've just installed the NFR USB version of ISE on an ESXi server.

The ISE boot just fine, but the default username/password (admin/cisco) dosn't work.

I'm trying to login to the Red Hat to set correct ip address etc.

The partno is:

ISE-1.0-MR2-NFR-USB

Anyone who have tried to install this and been able to login?

Thanks in advance

/Torben

Everyone's tags (1)
13 REPLIES
New Member

ISE NFR VMWare - Default username and password

The mentioned username/password combination is for the web interface only. The username/password for the CLI (RedHat as you call it) is provided during install. There is no default here.

tbg
New Member

ISE NFR VMWare - Default username and password

Thats correct for the ISO install.

But this is the NFR (Not-For-Resell) version on a USB Stick.

It's a complete VMware image, that is booting up the CLI (which is a RedHat :o) asking for a predefine username and password.

It's not asking for a new username/password combination, since the installation step has been provided by Cisco.

But no one seems to know this username/password.

/Torben

New Member

ISE NFR VMWare - Default username and password

Sorry for my misunderstanding. I was not aware of the fact that the NFR installation differs from the ISO install.

I don't think I can be of any help.

Maybe, based on the installation process of other cisco software, it could be:

L/P: cisco/cisco

L/P: Cisco/Cisco

Otherwise, is it possible to boot from the ISO to perform a password recovery procedure (Option 3 or 4)?

tbg
New Member

ISE NFR VMWare - Default username and password

I got the username/password from my local Cisco pusher

And it is:     admin/default1A

Nice to know.

/Torben

New Member

ISE NFR VMWare - Default username and password

Great info, thanks.

What ESXi version/procedure was used to install it? I keep getting error message "unsupported disk type, code 7" when I start the NFR VM in both 4.1 and 5.0

Thanks // Jan

tbg
New Member

ISE NFR VMWare - Default username and password

I use ESXi 5.0.

To install the ISE NFR, I used "VMware vCenter Converter Standalone":

  1. Choose Convert machine
  2. Select source type: Backup image or third-party virtual machine
  3. Select destination type: VMware Infrastructure virtual machine
  4. Choose Next a couple of times, and Finish
  5. Boot the ISR, login and change ip address/gateway
New Member

ISE NFR VMWare - Default username and password

Thanks. Tried that, but it fails saying "missig catalog file" using VMware converter 4.

NFR files unpack without errors and creates these files:

- ISE_1.0MR2.vmdk

- ....vmsd

- ....vmx

- ....vmxf

- ....nvram

- vmware

- vmware-0

- vmware-1

- vmware-2

Any files missing (corrupt tar file?) or am I forgetting something else?

New Member

Re: ISE NFR VMWare - Default username and password

Those are the same files I have. I just followed Torben's instructions using VMware converter 5 and it worked. thanks!

Cisco Employee

ISE NFR VMWare - Default username and password

Yes, I have the same ISE_1.0MR2 and the admin/default1A combination worked.

I'm working on running ISE NFR appliance under VMware Player 4.0.4 build-744019. Mike Wenstrom

New Member

Use one that you created

Use one that you created during VM setup in VMware.

 

New Member

Try the followingadmin

Try the following

admin ISEc0ld

New Member

The ISE 1.2 NFR on USB stick

The ISE 1.2 NFR on USB stick does indeed use admin/ISEc0ld as the default CLI credentials. Confirmed in my own lab mere minutes ago!

Cisco Employee

ISE NFR comes with admin

ISE NFR comes with admin/default1A as username and password

8465
Views
55
Helpful
13
Replies
CreatePlease to create content