Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Bronze

PPPoE Unable to ping

I'm trying to configure PPPoE between two routers ...PPPoE is establishing , but unable to ping

Server

username R4 password 0 CISCO

bba-group pppoe CISCO

virtual-template 1

interface Virtual-Template1

ip address 19.19.34.3 255.255.255.0

peer default ip address pool pool

ppp authentication chap

!

ip local pool pool 19.19.34.4

----------------------------

interface FastEthernet0/1

pppoe enable group global

pppoe-client dial-pool-number 1

interface Dialer1

mtu 1492

ip address negotiated

encapsulation ppp

dialer pool 1

dialer idle-timeout 0

dialer persistent

ppp authentication chap callin

ppp chap hostname R4

ppp chap password 0 CISCO

no cdp enable

*Feb 10 18:32:04.595: %DIALER-6-BIND: Interface Vi2 bound to profile Di1

*Feb 10 18:32:04.599: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up

*Feb 10 18:32:04.599: Vi2 PPP: Sending cstate UP notification

*Feb 10 18:32:04.599: Vi2 PPP: Processing CstateUp message

*Feb 10 18:32:04.603: PPP: Alloc Context [49B191F8]

*Feb 10 18:32:04.603: ppp13 PPP: Phase is ESTABLISHING

*Feb 10 18:32:04.603: Vi2 PPP: Using dialer call direction

*Feb 10 18:32:04.603: Vi2 PPP: Treating connection as a callout

*Feb 10 18:32:04.603: Vi2 PPP: Session handle[DE00000E] Session id[13]

*Feb 10 18:32:04.603: Vi2 LCP: Event[OPEN] State[Initial to Starting]

*Feb 10 18:32:04.603: Vi2 PPP: No remote authentication for call-out

*Feb 10 18:32:04.603: Vi2 LCP: O CONFREQ [Starting] id 1 len 14

*Feb 10 18:32:04.603: Vi2 LCP:    MRU 1492 (0x010405D4)

*Feb 10 18:32:04.603: Vi2 LCP:    MagicNumber 0x19869166 (0x050619869166)

*Feb 10 18:32:04.603: Vi2 LCP: Event[UP] State[Starting to REQsent]

*

R4#Feb 10 18:32:04.607: Vi2 LCP: I CONFREQ [REQsent] id 1 len 19

*Feb 10 18:32:04.607: Vi2 LCP:    MRU 1492 (0x010405D4)

*Feb 10 18:32:04.607: Vi2 LCP:    AuthProto CHAP (0x0305C22305)

*Feb 10 18:32:04.607: Vi2 LCP:    MagicNumber 0x177669A8 (0x0506177669A8)

*Feb 10 18:32:04.607: Vi2 LCP: O CONFACK [REQsent] id 1 len 19

*Feb 10 18:32:04.607: Vi2 LCP:    MRU 1492 (0x010405D4)

*Feb 10 18:32:04.607: Vi2 LCP:    AuthProto CHAP (0x0305C22305)

*Feb 10 18:32:04.607: Vi2 LCP:    MagicNumber 0x177669A8 (0x0506177669A8)

*Feb 10 18:32:04.607: Vi2 LCP: Event[Receive ConfReq+] State[REQsent to ACKsent]

*Feb 10 18:32:04.607: Vi2 LCP: I CONFACK [ACKsent] id 1 len 14

*Feb 10 18:32:04.607: Vi2 LCP:    MRU 1492 (0x010405D4)

*Feb 10 18:32:04.607: Vi2 LCP:    MagicNumber 0x19869166 (0x050619869166)

*Feb 10 18:32:04.607: Vi2 LCP: Event[Receive ConfAck] State[ACKsent to Open]

*Feb 10 18:32:04.607: Vi2 PPP: Queue CHAP code[1] id[1]

*Feb 10 18:32:04.619: Vi2 PPP: Phase is AUTHENTICATING, by the peer

*Feb 10 18:32:04.619: Vi2 CHAP: Redirect packet to Vi2

*Feb 10 18:32:04.619: Vi2 CHAP: I CHALLENGE id 1 len 23 from "R3"

*Feb 10 18:32:04.619: Vi2 LCP: State is Open

*Feb 10 18:32:04.619: Vi2 CHAP: Using hostname from interface CHAP

*Feb 10 18:32:04.619: Vi2 CHAP: Using password from interface CHAP

*Feb 10 18:32:04.619: Vi2 CHAP: O RESPONSE id 1 len 23 from "R4"

*Feb 10 18:32:04.631: Vi2 CHAP: I SUCCESS id 1 len 4

*Feb 10 18:32:04.631: Vi2 PPP: Phase is FORWARDING, Attempting Forward

*Feb 10 18:32:04.631: Vi2 PPP: Queue IPCP code[1] id[1]

*Feb 10 18:32:04.635: Vi2 PPP: Phase is ESTABLISHING, Finish LCP

*Feb 10 18:32:04.635: Vi2 PPP: Phase is UP

*Feb 10 18:32:04.635: Vi2 IPCP: Protocol configured, start CP. state[Initial]

*Feb 10 18:32:04.635: Vi2 IPCP: Event[OPEN] State[Initial to Starting]

*Feb 10 18:32:04.635: Vi2 IPCP: O CONFREQ [Starting] id 1 len 10

*Feb 10 18:32:04.635: Vi2 IPCP:    Address 0.0.0.0 (0x030600000000)

*Feb 10 18:32:04.635: Vi2 IPCP: Event[UP] State[Starting to REQsent]

*Feb 10 18:32:04.635: Vi2 PPP: Process pending ncp packets

*Feb 10 18:32:04.635: Vi2 IPCP: Redirect packet to Vi2

*Feb 10 18:32:04.635: Vi2 IPCP: I CONFREQ [REQsent] id 1 len 10

*Feb 10 18:32:04.635: Vi2 IPCP:    Address 19.19.34.3 (0x030613132203)

*Feb 10 18:32:04.635: Vi2 IPCP: O CONFACK [REQsent] id 1 len 10

*Feb 10 18:32:04.639: Vi2 IPCP:    Address 19.19.34.3 (0x030613132203)

*Feb 10 18:32:04.639: Vi2 IPCP: Event[Receive ConfReq+] State[REQsent to ACKsent]

*Feb 10 18:32:04.639: Vi2 IPCP: I CONFNAK [ACKsent] id 1 len 10

*Feb 10 18:32:04.639: Vi2 IPCP:    Address 19.19.34.4 (0x030613132204)

*Feb 10 18:32:04.639: Vi2 IPCP: O CONFREQ [ACKsent] id 2 len 10

*Feb 10 18:32:04.639: Vi2 IPCP:    Address 19.19.34.4 (0x030613132204)

*Feb 10 18:32:04.639: Vi2 IPCP: Event[Receive ConfNak/Rej] State[ACKsent to ACKsent]

*Feb 10 18:32:04.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up

*Feb 10 18:32:04.643: Vi2 IPCP: I CONFACK [ACKsent] id 2 len 10

*Feb 10 18:32:04.643: Vi2 IPCP:    Address 19.19.34.4 (0x030613132204)

*Feb 10 18:32:04.643: Vi2 IPCP: Event[Receive ConfAck] State[ACKsent to Open]

*Feb 10 18:32:04.651: Vi2 IPCP: State is Open

*Feb 10 18:32:04.651: Di1 IPCP: Install negotiated IP interface address 19.19.34.4

*Feb 10 18:32:04.655: Di1 Added to neighbor route AVL tree: topoid 0, address 19.19.34.3

*Feb 10 18:32:04.655: Di1 IPCP: Route not installed to 19.19.34.3

1 REPLY
New Member

PPPoE Unable to ping

Please go through the link below may help you to configure the router

http://www.dslreports.com/faq/10952

225
Views
0
Helpful
1
Replies
CreatePlease login to create content