Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

ACE context syslog

Hi!

Does someone know how to configure the syslog under a context?

The syslog should be send via public interface. No additional management interface should be configured.

Any ideas?

1 ACCEPTED SOLUTION

Accepted Solutions
Silver

Re: ACE context syslog

Can you configure for example:

logging trap 6

This specifies that messages between 0-6 are send to the syslog server specified by the "logging host" command.

I don't know which severity is the default value.

7 REPLIES
Silver

Re: ACE context syslog

Hi,

you can configure syslog under each context separatly.

Please refer to following document.

http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/system/message/guide/config.html#wp1059844

Normally, the ACE will use its public interface due to its routing table (default route is pointing to public interface)

Hope this helps!

New Member

Re: ACE context syslog

I configured it as described in the manual.

In the Admin context it works. In a sub-context not. No Packets are sent by the ACE appliance.

Any other ideas or working configurations?

Silver

Re: ACE context syslog

I'm using it in different contexts and it works fine.

can you upload your config?

New Member

Re: ACE context syslog

The configuration is basicly:

logging enable

logging fastpath

logging console 1

logging timestamp

logging buffered 5

logging persistent 6

logging monitor 5

logging facility 21

logging queue 1024

logging device-id context-name

logging host 195.122.17.210 udp/514

logging rate-limit 42 60 level 5

logging rate-limit 42 60 level 6

logging rate-limit 42 60 level 7

access-list V101-IN line 1 extended permit icmp 195.122.1.0 255.255.255.0 195.

122.1.0 255.255.255.0

access-list V101-IN line 2 extended permit icmp any host 195.122.1.6

access-list V101-IN line 3 extended permit icmp any host 195.122.1.5

access-list V101-IN line 10 extended permit icmp any host 195.122.1.17

access-list V101-IN line 20 extended permit icmp any host 195.122.1.18

access-list V101-IN line 30 extended permit icmp any host 195.122.1.19

access-list V101-IN line 40 extended permit tcp any host 195.122.1.17 eq www

access-list V101-IN line 50 extended permit tcp any host 195.122.1.18 eq www

access-list V101-IN line 60 extended permit tcp any host 195.122.1.19 eq www

access-list V101-IN line 68 extended permit tcp any host 195.122.1.17 eq https

interface vlan 3

description WL-Server-Frontend

ip address 10.125.145.253 255.255.255.0

alias 10.125.145.254 255.255.255.0

peer ip address 10.125.145.252 255.255.255.0

service-policy input ICMP-ALLOW

no shutdown

interface vlan 101

description outside

ip address 195.122.1.5 255.255.255.0

alias 195.122.1.6 255.255.255.0

peer ip address 195.122.1.4 255.255.255.0

access-group input V101-IN

service-policy input L4-V101-LB

no shutdown

ip route 0.0.0.0 0.0.0.0 195.122.1.1

Silver

Re: ACE context syslog

Can you configure for example:

logging trap 6

This specifies that messages between 0-6 are send to the syslog server specified by the "logging host" command.

I don't know which severity is the default value.

New Member

Re: ACE context syslog

Great it works!!

Many THX!

Silver

Re: ACE context syslog

your welcome, thanks for the rating

301
Views
0
Helpful
7
Replies