Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

CE505 boot problem. Help needed, ASAP

One day old (still rocks! :)) working CE-505 stop booting with:

--- boot msg ---

Press any key to stop auto-boot...

0

auto-booting...

boot device (flash,net) [ net]:

file name [ ce505-cache-231.bin]:

cache IP address [ 192.168.0.99]:

IP network mask [ 255.255.255.0]:

server IP address [ 192.168.0.10]:

protocol (rcp,ftp,tftp) [ tftp]:

flags [ 0]:

Loading from the network

Attaching network interface fei0... done.

Attaching network interface lo0... done.

Loading... Starting at 0x108000...

#!ImageInfo

#

# +--------------------+

# | CISCO CE image |

# +--------------------+

#

SUPPORTED_PRODUCTS=CE505,CE550

UNCOMPRESSED_CKSUM=0xf17c87d3

UNCOMPRESSED_SIZE=0x3578b8

COMPRESSED_CKSUM=0xd6ab0b3

COMPRESSED_SIZE=0x167cdb

#

This image supports models CE505,CE550 and this appliance is a 00000.

Press any key to stop auto-boot...

--- boot msg ---

And start timer again :( I tryed booting from network because flash boot fails similar above. I see IOS booting message and then boot counter again :(

Can any one help me with this issue?

P.S. Sorry for my english.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: CE505 boot problem. Help needed, ASAP

Paul,

This indicates that the flash is corrupted. You will need to RMA/replace the device.

~Zach

7 REPLIES
Cisco Employee

Re: CE505 boot problem. Help needed, ASAP

Paul,

This indicates that the flash is corrupted. You will need to RMA/replace the device.

~Zach

New Member

Re: CE505 boot problem. Help needed, ASAP

THANK YOU! but... how this can be? i opened this black box and this is PC! mabe if i clean BIOS by removing battery helps? i realy don't have any idea :(

Cisco Employee

Re: CE505 boot problem. Help needed, ASAP

The flash contains specific information about the hardware that is used by our software to determine which versions are supported, what drivers to use, etc. In our newer hardware, we support re-writing the flash by booting from a special rescue CD. Since the CE505 does not have a CD-ROM drive, flash corruption is resolved by replacing the device.

~Zach

New Member

Re: CE505 boot problem. Help needed, ASAP

i have two working ce-505 and can i read his flash data and write it on corrupted flash? or can you recommend cisco's partner in rusia who can repair this device?

Cisco Employee

Re: CE505 boot problem. Help needed, ASAP

You would not be able to restore the flash from another working CE.

You can search for Cisco partners using the Partner Locator tool on CCO:

http://tools.cisco.com/WWChannels/LOCATR/jsp/partner_locator.jsp

regards,

Zach

New Member

Re: CE505 boot problem. Help needed, ASAP

THANK YOU! again

New Member

Re: CE505 boot problem. Help needed, ASAP

It's me again with another CE 505. I van't understand what happens, but one day flash boot fail and i try to boot from network:

--------------------

auto-booting...

boot device (flash,net) [ net]:

file name [ ce505-cache-251.bin]:

cache IP address [ 10.10.10.120]:

IP network mask [ 255.255.255.0]:

server IP address [ 10.10.10.10]:

protocol (rcp,ftp,tftp) [ tftp]:

flags [ 0]:

Loading from the network

Attaching network interface fei0... done.

Attaching network interface lo0... done.

Loading... image read failed: Image is not for x86 CPU: errno=0x16

Error loading file: errno = 0x31.

Can't load boot file!!

--------------------

Why CE can't boot? I downloaded image from anothe working CE

Thank you.

170
Views
0
Helpful
7
Replies
CreatePlease to create content