This is all I get when I do a show int vlan 13. I would like to see the other coutners to prove that I am forceing traffic through that interface and it is not going through the router that I want to shut off. I was told it is because of the F2 card N7K-F248XP-25. Show int vlan x counters shows nothing. Is there any way around this. Ho do the engineers proove that a vlan interface is dropping packets or needs to have buffers tweeked when they can't even see if there are any drops on the interface. I have a number of interfaaces with the same vlans on them so i can't really look at a interface to see if it is an issue for a vlan. There is a big diffrence between a show int vlan and a show int e3/1
Aggr-A# show int vlan 13 Vlan13 is up, line protocol is up Hardware is EtherSVI, address is 4055.390e.7043 Internet Address is 10.2.2.253/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not supported ARP type: ARPA Last clearing of "show interface" counters never
Aggr-A# sh int e3/1 Ethernet3/1 is up admin state is up, Dedicated Interface Belongs to Po1 Hardware: 1000/10000 Ethernet, address: 6c20.5613.b790 (bia 6c20.5613.b790) Description: vpc peer link MTU 9216 bytes, BW 10000000 Kbit, DLY 10 usec reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, medium is broadcast Port mode is trunk full-duplex, 10 Gb/s, media type is 10G Beacon is turned off Auto-Negotiation is turned on Input flow-control is off, output flow-control is off Auto-mdix is turned on Rate mode is dedicated Switchport monitor is off EtherType is 0x8100 EEE (efficient-ethernet) : n/a Last link flapped 1week(s) 5day(s) Last clearing of "show interface" counters never 1 interface resets 30 seconds input rate 688 bits/sec, 0 packets/sec 30 seconds output rate 1472 bits/sec, 1 packets/sec Load-Interval #2: 5 minute (300 seconds) input rate 112 bps, 0 pps; output rate 1.05 Kbps, 1 pps RX 186006 unicast packets 729657 multicast packets 1 broadcast packets 730649 input packets 73282781 bytes 0 jumbo packets 0 storm suppression packets 0 runts 0 giants 0 CRC 0 no buffer 0 input error 0 short frame 0 overrun 0 underrun 0 ignored 0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop 0 input with dribble 0 input discard 0 Rx pause TX 185106 unicast packets 5352448 multicast packets 15708 broadcast packets 1921053 output packets 185455510 bytes 0 jumbo packets 0 output error 0 collision 0 deferred 0 late collision 0 lost carrier 0 no carrier 0 babble 0 output discard 0 Tx pause
The unmanaged mode is also known as Network only switching, which is introduced in Brazos release. It adds the flexibility for customer to use only network automation for service appliance.
If a device is configured a...
Usually, we can access ESXi Shell by pressing Alt+F1 from ESXi DCUI (Direct Console User Interface).
But on HyperFlex system, it just shows black window.
This is expected behavior because HyperFlex redirects ESXi Shell output to SoL...
Configuring an Export Policy Using the GUI
This procedure explains how to configure an Export policy using the APIC GUI. Follow these steps to trigger a backup of your data:
On the menu bar, choose Admi...