Anyone tried using LDAP_PROBE (that is shipped by default) for load-balancing/fail-over of IBM Tivoli Directory Server?
I have tried the default script that does ananymous bind , but it doesnt do the job. I suspect if the response returned from Tivoli directory server is not in same format as expected but how do i check the response format and check the offset of status in response.
Attaching the script and debug output.
probe scripted LDAP-Probe-389
passdetect count 2
script LDAP_PROBE_3.tcl DEBUG
2013 Oct 31 09:47:35.478652 scripted_hm: (ctx:3) TCLWT (scripted_hm_run_probe_msg): Received MTS_RUN_MSG
2013 Oct 31 09:47:35.478732 scripted_hm: (ctx:3)tcl_wt_create_qnode: temp_qnode 0x100301a0 em_msg 0x2c94f854
2013 Oct 31 09:47:35.478764 scripted_hm: (ctx:3) TCL_UTIL(hm_tcl_associate_script_buf) - ENTER em_msg = 0x2c94f854
2013 Oct 31 09:47:35.478791 scripted_hm: (ctx:3) TCL_UTIL (hm_tcl_associate_script_buf) : Associating script-buf with LDAP_PROBE_3.tcl em_msg = 0x2c94f854
2013 Oct 31 09:47:35.478821 scripted_hm: (ctx:3) TCL_UTIL(hm_tcl_find_script_buf) - ENTER
2013 Oct 31 09:47:35.478848 scripted_hm: (ctx:3) TCL_UTIL(hm_tcl_find_script_buf) - Found script buf
2013 Oct 31 09:47:35.478872 scripted_hm: (ctx:3)TCL_UTIL(hm_tcl_associate_script_buf) - EXIT
2013 Oct 31 09:47:35.478899 scripted_hm: (ctx:3) TCLWT(tcl_wt_create_qnode): Created qnode 100301a0
2013 Oct 31 09:47:35.483629 scripted_hm: (ctx:3)hm_tcl_run: pid 9916 return_fd 17
2013 Oct 31 09:47:35.490360 scripted_hm: (ctx:3) TCL_UTIL(hm_tcl_set_env_vars): arg list = DEBUG
2013 Oct 31 09:47:35.490416 scripted_hm: (ctx:3) TCL_UTIL(hm_tcl_get_argcount) - ENTER, argv(DEBUG)
2013 Oct 31 09:47:35.490618 scripted_hm: (ctx:3)hm_tcl_run: About to run the TCL interpreter
2013 Oct 31 09:47:35.498609 scripted_hm: (ctx:3)Tcl_Itasca_SocketObjCmd: g_num_socket 1
2013 Oct 31 09:47:35.502149 scripted_hm: (ctx:3) TCLPROBE(hm_tcl_exit_proc): File open failed
2013 Oct 31 09:47:35.502169 scripted_hm: (ctx:3)TCL-WT(tcl_wt_process_interp_return) - ENTER
2013 Oct 31 09:47:35.502226 scripted_hm: (ctx:3) TCLWT(tcl_wt_process_interp_return): received error from scripted probe!
2013 Oct 31 09:47:35.502265 scripted_hm: (ctx:3) TCLWT(tclwt_send_em_msg): ENTER
This document will provide screenshots to outline the steps to setup
TACACS+ configuration to ACI and also the configuration required on
Cisco ACS server. Please find the official Cisco guide for configuring
TACACS+ Authentication to ACI:
Is it supported or NOT supported? It's a frequently asked question.
Before APIC, release 2.3(1f), transit routing was not supported within a
single L3Out profile. In APIC, release 2.3(1f) and later, you can
configure transit routing with a single L3Out pr...
Cisco Documents are usually accurate, but when it came to the document
on Cisco APIC Signature-Based Transactions it was slightly off the mark.
This document is for those novices to API like me who cant seem to
figure out how to go about performing signat...