Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Outboud call configuration in SPA8800 with Asterisk

I am trying to configure SAP8800 under Asterisk environment.  Doing exactly per document "Configuring the Cisco SPA8800 Telephony Gateway in an Asterisk Environment.

I am able to dial in from an outside phone to both SPA8800 analog phones as well as soft phone extension configured in Asterisk.  However, I am unable to dial out from either SPA8800 analog phones or soft phone extensions in Asterisk.

SPA8800 settings are exactly as shown in the document.  The document shows a dial plan (Voice->Line 2) for Incoming Call in Line 2 to route it to extension 101.  However, there is no visible setting to route the Outgoing Calls, from Asterisk SIP phones or SPA8800 analog lines, to any PSTN line.

What am I missing?   Below are my configuration settings in Asterisk. (I am using FreePBX, so got to use the *custom* conf files)

****** in sip_general_additional.conf  *******

;define SPA8800 pstn2 user

[pstn2]

type=friend

host=10.10.10.10

port=5161

PA8800 pstn2 user

[pstn2]

type=friend

host=10.10.10.10

port=5161

dtmfmode=rfc2833

context=pstn2

insecure=very

;

;define SPA8800 pstn3 user

[pstn3]

type=friend

host=10.10.10.10

port=5261

dtmfmode=rfc2833

context=pstn3

insecure=very

**** in extensions_custom.conf *******

; SPA8800 configurations

;outbound dialing

[fxsgroup]

;

;

; dial 7 to explicitly use FXO3

exten => _7.,1,Dial(SIP/${EXTEN:1}@pstn3,60,r)

;

; dial 8 as a steering digit:

; if FXO2 is not available, FXO3 will be used

; if FXO3 is not available, the user hears congestion

exten => _8.,1,Dial(SIP/${EXTEN:1}@pstn1,60,r)

exten => _8.,1,Dial(SIP/${EXTEN:1}@pstn2,60,r)

exten => _8.,2,Dial(SIP/${EXTEN:1}@pstn3,60,r)

;

; dial 9 to explicitly use ITSP

exten => _9.,1,Dial(SIP/${EXTEN:1}@itsp1,30,r)

;

; r causes ringing for calling party but audio is

; not passed until called party answers call

;  T allows caller to transfer with #

exten => 101,1,Dial(SIP/101,60,rT)

exten => 102,1,Dial(SIP/102,60,rT)

exten => 103,1,Dial(SIP/103,60,rT)

exten => 104,1,Dial(SIP/104,60,rT)

exten => 200,1,Dial(SIP/200,60,rT)

exten => 201,1,Dial(SIP/201,60,rT)

;exten => 1001,1,Dial(SIP/1001,60,rT)

;exten => XXXX,1,Dial(SIP/${EXTEN},60,rT)

;

Everyone's tags (1)
1 REPLY
Cisco Employee

Re: Outboud call configuration in SPA8800 with Asterisk

Hi smartswami,

Take a look at this thread, perhaps it will help answer your question. If not, let me know and I'll try to be more specific.
https://www.myciscocommunity.com/message/18728#18728

Regards,

Patrick

-----------

3129
Views
0
Helpful
1
Replies
CreatePlease to create content