Introduction
This document covers the Configuration procedures to enable Video and Camera support on Cisco Unified SIP-IP Phone 9971 using Cisco Unified Communications Manager Express 8.6 .
Prerequisites
- Cisco Unified CME 8.6 or a later version
Components Used
- Cisco Unified CME 8.6
- Cisco IP Phone 9971
This Procedure is applicable to Cisco IP Phones 9951 and 9971.
Configuration
- Cisco Unified IP Phone 9971 supports only the SIP firmware files.
- Download the SIP firmware file for IP Phone 9971 from Cisco Software download site with your Cisco login. Refer the screenshot for Product selection.
- SIP IP Phone is supported only on specified platforms. Refer the section "Supported Platforms and Memory Specifications: SIP IP Phones*" in the url:
Cisco Unified CME 8.6 Supported Firmware, Platforms, Memory, and Voice Products
To enable video and camera support on Cisco Unified IP Phone 9971, follow these steps:
Step 1: Voice register global configuration
Router# configure terminal
Router(config)#voice register global
Router(config-register-global)#camera
Router(config-register-global)#video
Note Make sure you configure video command without configuring the camera command so that Cisco Unified IP phones 9951 and 9971 can switch from phose based video camera to CUVA. If you configure both video and camera commands together, you may need to manually remove the USB camera from the Cisco Unified IP phones 9951 and 9971.
Step 2: Create Profile
Router(config-register-global)# create profile
Generates provisioning files required for SIP phones and writes the file to the location specified with the tftp-path command.
Router(config-register-global)#exit
Step3: Voice register pool configuration
Router(config)#voice register pool 5
Router(config-register-pool)#id mac 0009.A3D4.1234
Explicitly identifies a locally available individual SIP phone to support a degree of authentication.
Router(config-register-pool)#camera
Router(config-register-pool)#video
Enables camera, video command under voice register pool configuration mode.
Router(config-register-pool)#exit
Step4: Voice register template configuration
Router(config)voice register template 10
Enters voice register template configuration mode to define a template of common parameters for SIP phones in Cisco Unified CME.
• Range: 1 to 5.
Router(config-register-template)#camera
Router(config-register-template)#video
Configures camera,video command under voice register template configuration mode.
Router(config-register-template)# end
Step5: Apply configuration
Apply-config is similar to resetting or restarting the phones and allowing the phones to update phone configuration files. Phones only reboot if needed.To apply video configuration to Cisco Unified IP phones 8961, 9951 and 9971, follow these steps:
Router# configure terminal
Router(config)#voice register pool 5
Router(config-register-pool)#apply-config
Sample CME 8.6 Configuration
The following example shows camera and video commands configured in voice register global: Router#show run ! ! voice service voip allow-connections sip to sip fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none ! ! voice register global mode cme bandwidth video tias-modifier 244 negotiate end-to-end max-pool 10 camera video ! voice register template 10 ! The following example shows video and camera commands configured under voice register pool 5, you can also configure both camera and video commands under voice register template: Router#show run ! ! voice service voip allow-connections sip to sip fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none ! ! voice register global mode cme bandwidth video tias-modifier 244 negotiate end-to-end max-pool 10 ! voice register pool 1 id mac 1111.1111.1111 ! voice register pool 4 ! voice register pool 5 logout-profile 58 id mac 0009.A3D4.1234 camera video ! |
|
Related Information