Hi this is the configuration of my router 2801:
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname XXXXXX
!
boot-start-marker
boot system flash:c2801-spservicesk9-mz.123-14.T6.bin
boot-end-marker
!
logging buffered 51200 warnings
!
aaa new-model
!
!
aaa authentication login default group radius local
!
aaa session-id common
!
resource policy
!
clock timezone Milano 2
clock summer-time CET recurring
network-clock-participate wic 3
network-clock-select 1 BRI0/3/0
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip domain name XXXXXXXXXXXX
ip name-server XXXXXXXXXXXXX
no ftp-server write-enable
isdn switch-type basic-net3
isdn logging
!
voice-card 0
!
!
!
voice service voip
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
!
!
!
!
!
!
!
!
!
username XXXXXXXXXXXX privilege 15 secret 5 XXXXXXXXX
!
!
!
!
interface FastEthernet0/0
no ip address
speed 100
full-duplex
!
interface FastEthernet0/0.100
description *** Link to 2950 Fa0/23 ***
encapsulation dot1Q 100
ip address XXXXXXXXX XXXXXXXXXXX
no snmp trap link-status
no cdp enable
!
interface FastEthernet0/0.130
description *** Link to 2950 Fa0/23 ***
encapsulation dot1Q 130
ip address XXXXXXXXXXXXXX XXXXXXXXXXXXXXX
no snmp trap link-status
no cdp enable
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface BRI0/3/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn bind-l3 ccm-manager service mgcp
isdn sending-complete
!
interface BRI0/3/1
no ip address
shutdown
isdn switch-type basic-net3
isdn point-to-point-setup
!
ip classless
ip route 0.0.0.0 0.0.0.0 XXXXXXXXXXXXXX
!
no cdp run
!
!
radius-server host XXXXXXXXXXXX auth-port 1812 acct-port 1813
radius-server key 7 XXXXXXXXXXXX
!
control-plane
voice-port 0/3/0
output attenuation 10
echo-cancel coverage 32
no vad
compand-type a-law
cptone IT
!
voice-port 0/3/1
!
ccm-manager mgcp
!
mgcp
mgcp call-agent XXXXXXXXX service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode cisco
mgcp validate domain-name
mgcp fax t38 inhibit
!
mgcp profile default
!
!
!
dial-peer voice 100 pots
description *** Gestione Chiamate Voce in Uscita ***
preference 1
service mgcp
destination-pattern .
port 0/3/0
!
dial-peer voice 555 voip
description *** Gestione Chiamate Voce in Ingresso ***
preference 1
service mgcp
destination-pattern XXXXXXXX
progress_ind setup enable 3
session target ipv4:XXXXXXXXXXXX
incoming called-number .
dtmf-relay h245-alphanumeric
!
dial-peer voice 556 voip
description *** Gestione chiamate Verso FAX ***
preference 1
service mgcp
destination-pattern XXXXXXXXXX
translate-outgoing called 1
modem passthrough nse codec g711ulaw
session target ipv4:XXXXXXXXX
incoming called-number .
dtmf-relay h245-signal h245-alphanumeric
fax rate disable
no vad
!
banner motd ^CC
^C
!
line con 0
line aux 0
line vty 0 4
privilege level 15
transport input ssh
line vty 5 15
privilege level 15
transport input ssh
!
ntp clock-period 17179212
ntp server XXXXXXXXXXXX
end
------------------------
When i make a call from my phone to an outside numeber...if there is an IVR that aswer the call, i can pilot it with my phone digit(dtmf). It seems that my router do not relay the DTMF tones...
anybody have an idea?
Thanks so much.
Claudio
BR,
Claudio
