Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

DTMF relay for outgoing call

Hi this is the configuration of my router 2801:

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname XXXXXX

!

boot-start-marker

boot system flash:c2801-spservicesk9-mz.123-14.T6.bin

boot-end-marker

!

logging buffered 51200 warnings

!

aaa new-model

!

!

aaa authentication login default group radius local

!

aaa session-id common

!

resource policy

!

clock timezone Milano 2

clock summer-time CET recurring

network-clock-participate wic 3

network-clock-select 1 BRI0/3/0

mmi polling-interval 60

no mmi auto-configure

no mmi pvc

mmi snmp-timeout 180

ip subnet-zero

ip cef

!

!

no ip dhcp use vrf connected

!

!

ip domain name XXXXXXXXXXXX

ip name-server XXXXXXXXXXXXX

no ftp-server write-enable

isdn switch-type basic-net3

isdn logging

!

voice-card 0

!

!

!

voice service voip

!

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

!

!

!

!

!

!

!

!

!

username XXXXXXXXXXXX privilege 15 secret 5 XXXXXXXXX

!

!

!

!

interface FastEthernet0/0

no ip address

speed 100

full-duplex

!

interface FastEthernet0/0.100

description *** Link to 2950 Fa0/23 ***

encapsulation dot1Q 100

ip address XXXXXXXXX XXXXXXXXXXX

no snmp trap link-status

no cdp enable

!

interface FastEthernet0/0.130

description *** Link to 2950 Fa0/23 ***

encapsulation dot1Q 130

ip address XXXXXXXXXXXXXX XXXXXXXXXXXXXXX

no snmp trap link-status

no cdp enable

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface BRI0/3/0

no ip address

isdn switch-type basic-net3

isdn point-to-point-setup

isdn incoming-voice voice

isdn bind-l3 ccm-manager service mgcp

isdn sending-complete

!

interface BRI0/3/1

no ip address

shutdown

isdn switch-type basic-net3

isdn point-to-point-setup

!

ip classless

ip route 0.0.0.0 0.0.0.0 XXXXXXXXXXXXXX

!

no cdp run

!

!

radius-server host XXXXXXXXXXXX auth-port 1812 acct-port 1813

radius-server key 7 XXXXXXXXXXXX

!

control-plane

voice-port 0/3/0

output attenuation 10

echo-cancel coverage 32

no vad

compand-type a-law

cptone IT

!

voice-port 0/3/1

!

ccm-manager mgcp

!

mgcp

mgcp call-agent XXXXXXXXX service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode cisco

mgcp validate domain-name

mgcp fax t38 inhibit

!

mgcp profile default

!

!

!

dial-peer voice 100 pots

description *** Gestione Chiamate Voce in Uscita ***

preference 1

service mgcp

destination-pattern .

port 0/3/0

!

dial-peer voice 555 voip

description *** Gestione Chiamate Voce in Ingresso ***

preference 1

service mgcp

destination-pattern XXXXXXXX

progress_ind setup enable 3

session target ipv4:XXXXXXXXXXXX

incoming called-number .

dtmf-relay h245-alphanumeric

!

dial-peer voice 556 voip

description *** Gestione chiamate Verso FAX ***

preference 1

service mgcp

destination-pattern XXXXXXXXXX

translate-outgoing called 1

modem passthrough nse codec g711ulaw

session target ipv4:XXXXXXXXX

incoming called-number .

dtmf-relay h245-signal h245-alphanumeric

fax rate disable

no vad

!

banner motd ^CC

^C

!

line con 0

line aux 0

line vty 0 4

privilege level 15

transport input ssh

line vty 5 15

privilege level 15

transport input ssh

!

ntp clock-period 17179212

ntp server XXXXXXXXXXXX

end

------------------------

When i make a call from my phone to an outside numeber...if there is an IVR that aswer the call, i can pilot it with my phone digit(dtmf). It seems that my router do not relay the DTMF tones...

anybody have an idea?

Thanks so much.

Claudio

BR,

Claudio

1 REPLY
New Member

Re: DTMF relay for outgoing call

I solved the problem,

my IOS release is bugged. 12.3XX

i've installed the new release 12.4 and everithing works.

BR.

180
Views
0
Helpful
1
Replies
CreatePlease to create content