04-12-2006 11:18 PM - edited 03-13-2019 11:40 PM
Hi this is the configuration of my router 2801:
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname XXXXXX
!
boot-start-marker
boot system flash:c2801-spservicesk9-mz.123-14.T6.bin
boot-end-marker
!
logging buffered 51200 warnings
!
aaa new-model
!
!
aaa authentication login default group radius local
!
aaa session-id common
!
resource policy
!
clock timezone Milano 2
clock summer-time CET recurring
network-clock-participate wic 3
network-clock-select 1 BRI0/3/0
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip domain name XXXXXXXXXXXX
ip name-server XXXXXXXXXXXXX
no ftp-server write-enable
isdn switch-type basic-net3
isdn logging
!
voice-card 0
!
!
!
voice service voip
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
!
!
!
!
!
!
!
!
!
username XXXXXXXXXXXX privilege 15 secret 5 XXXXXXXXX
!
!
!
!
interface FastEthernet0/0
no ip address
speed 100
full-duplex
!
interface FastEthernet0/0.100
description *** Link to 2950 Fa0/23 ***
encapsulation dot1Q 100
ip address XXXXXXXXX XXXXXXXXXXX
no snmp trap link-status
no cdp enable
!
interface FastEthernet0/0.130
description *** Link to 2950 Fa0/23 ***
encapsulation dot1Q 130
ip address XXXXXXXXXXXXXX XXXXXXXXXXXXXXX
no snmp trap link-status
no cdp enable
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface BRI0/3/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn bind-l3 ccm-manager service mgcp
isdn sending-complete
!
interface BRI0/3/1
no ip address
shutdown
isdn switch-type basic-net3
isdn point-to-point-setup
!
ip classless
ip route 0.0.0.0 0.0.0.0 XXXXXXXXXXXXXX
!
no cdp run
!
!
radius-server host XXXXXXXXXXXX auth-port 1812 acct-port 1813
radius-server key 7 XXXXXXXXXXXX
!
control-plane
voice-port 0/3/0
output attenuation 10
echo-cancel coverage 32
no vad
compand-type a-law
cptone IT
!
voice-port 0/3/1
!
ccm-manager mgcp
!
mgcp
mgcp call-agent XXXXXXXXX service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode cisco
mgcp validate domain-name
mgcp fax t38 inhibit
!
mgcp profile default
!
!
!
dial-peer voice 100 pots
description *** Gestione Chiamate Voce in Uscita ***
preference 1
service mgcp
destination-pattern .
port 0/3/0
!
dial-peer voice 555 voip
description *** Gestione Chiamate Voce in Ingresso ***
preference 1
service mgcp
destination-pattern XXXXXXXX
progress_ind setup enable 3
session target ipv4:XXXXXXXXXXXX
incoming called-number .
dtmf-relay h245-alphanumeric
!
dial-peer voice 556 voip
description *** Gestione chiamate Verso FAX ***
preference 1
service mgcp
destination-pattern XXXXXXXXXX
translate-outgoing called 1
modem passthrough nse codec g711ulaw
session target ipv4:XXXXXXXXX
incoming called-number .
dtmf-relay h245-signal h245-alphanumeric
fax rate disable
no vad
!
banner motd ^CC
^C
!
line con 0
line aux 0
line vty 0 4
privilege level 15
transport input ssh
line vty 5 15
privilege level 15
transport input ssh
!
ntp clock-period 17179212
ntp server XXXXXXXXXXXX
end
------------------------
When i make a call from my phone to an outside numeber...if there is an IVR that aswer the call, i can pilot it with my phone digit(dtmf). It seems that my router do not relay the DTMF tones...
anybody have an idea?
Thanks so much.
Claudio
BR,
Claudio
04-18-2006 04:39 AM
I solved the problem,
my IOS release is bugged. 12.3XX
i've installed the new release 12.4 and everithing works.
BR.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: