Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

DMP 4400 (URL's)

Hi,

In DMP 4400 5.2 firmware, what is the difference between (Media URL) and (URL to be Displayed)?

Is there any updated documentation for DMP-DM v5.2?

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: DMP 4400 (URL's)

The 5.2 DMP-DM  documentation is not available yet but here is

the information from 5.1.  I believe the only difference is that

the "Video URL" was renamed to "Media URL".

http://www.cisco.com/en/US/docs/video/digital_media_systems/5_x/5_1/dmp/user/guide/DMPDMcfg.html

---------------------------------------------------

Showing or Stopping Video Content from an HTTP URL

---------------------------------------------------

To show on your DMP display the video content from an HTTP URL,

or to stop showing that video content, do the following:

Procedure

---------

Step 1 In the Display Actions list, click Video URL.

Step 2 Enter or edit the required values.

Step 3 Do one of the following:

* To start showing the video content immediately, click Start.

* To stop showing the video content immediately, click Stop.

There might be a delay of as long as 3 seconds.

Video URL Description

---------------------

The HTTP URL. You can enter either an IP address or a routable

DNS name for the server and must also enter the full pathname

that points exactly to the video file on that server. The URL

cannot contain any more than 254 characters, cannot contain

any spaces, and must use ISO/IEC-8859 (Latin-1) character

encoding. If the HTTP service runs on a nonstandard logical

port, use the typical method (:80, for example) to include

a port number in the URL.

******************************************

------------------------------------------------------

Specifying the URL to Load on the HTML Content Plane

------------------------------------------------------

You can load a web page or other content on the HTML content plane (TVzilla). The HTTP URL that you enter persists until you use this procedure again to enter a different URL or until the next time that you restart your DMP. You cannot save the URL entry so that it persists after a restart.

Procedure

---------

Step 1 In the Display Actions list, click URL to be Displayed.

Step 2 Enter or edit the HTTP URL, and then click Go.

Step 3 (Optional) To stop showing the specified content, do one of the following:

* Click VIDEO button

* Enter an HTTP URL that points to different content, and then click Go.

URL To Be Displayed Description

-------------------------------

The HTTP URL that loads a web page (or other content)

on the HTML content plane. The URL cannot contain any

more than 254 characters, cannot contain any spaces,

and must use ISO/IEC-8859 (Latin-1) character encoding.

The main difference is the one URL access' the video plane and the other is the

BROWSER plane on the DMP.

If this answers your question, Please take time to mark this 
discussion answered & rate the response.  

Thank You! 

T.

1 REPLY
Cisco Employee

Re: DMP 4400 (URL's)

The 5.2 DMP-DM  documentation is not available yet but here is

the information from 5.1.  I believe the only difference is that

the "Video URL" was renamed to "Media URL".

http://www.cisco.com/en/US/docs/video/digital_media_systems/5_x/5_1/dmp/user/guide/DMPDMcfg.html

---------------------------------------------------

Showing or Stopping Video Content from an HTTP URL

---------------------------------------------------

To show on your DMP display the video content from an HTTP URL,

or to stop showing that video content, do the following:

Procedure

---------

Step 1 In the Display Actions list, click Video URL.

Step 2 Enter or edit the required values.

Step 3 Do one of the following:

* To start showing the video content immediately, click Start.

* To stop showing the video content immediately, click Stop.

There might be a delay of as long as 3 seconds.

Video URL Description

---------------------

The HTTP URL. You can enter either an IP address or a routable

DNS name for the server and must also enter the full pathname

that points exactly to the video file on that server. The URL

cannot contain any more than 254 characters, cannot contain

any spaces, and must use ISO/IEC-8859 (Latin-1) character

encoding. If the HTTP service runs on a nonstandard logical

port, use the typical method (:80, for example) to include

a port number in the URL.

******************************************

------------------------------------------------------

Specifying the URL to Load on the HTML Content Plane

------------------------------------------------------

You can load a web page or other content on the HTML content plane (TVzilla). The HTTP URL that you enter persists until you use this procedure again to enter a different URL or until the next time that you restart your DMP. You cannot save the URL entry so that it persists after a restart.

Procedure

---------

Step 1 In the Display Actions list, click URL to be Displayed.

Step 2 Enter or edit the HTTP URL, and then click Go.

Step 3 (Optional) To stop showing the specified content, do one of the following:

* Click VIDEO button

* Enter an HTTP URL that points to different content, and then click Go.

URL To Be Displayed Description

-------------------------------

The HTTP URL that loads a web page (or other content)

on the HTML content plane. The URL cannot contain any

more than 254 characters, cannot contain any spaces,

and must use ISO/IEC-8859 (Latin-1) character encoding.

The main difference is the one URL access' the video plane and the other is the

BROWSER plane on the DMP.

If this answers your question, Please take time to mark this 
discussion answered & rate the response.  

Thank You! 

T.

780
Views
0
Helpful
1
Replies
CreatePlease to create content