Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
2283
Views
0
Helpful
7
Replies

EEM Applet -- Can you set an Env Var from an Applet?

tproeber
Level 1
Level 1

‎11-26-2013 09:34 AM

The 900MhzTX Environment Variable is not getting set.  I'm trying to constantly display the radio data rates in the Sho-Run.  After this works I'll add for the RX and for the other 3 radios.

It runs successfully but doesn't set the Env Var.


event manager applet Radio-Reader

event timer watchdog time 10

action 010 cli command "enable"

action 020 cli command "ssh -l ubnt 192.168.2.11" pattern "assword:"

action 030 cli command "fly2the*" pattern "#"

action 040 cli command "mca-status" pattern "#"

action 050 regexp "wlanTxRate=([0-9\.]+)" $_cli_result

action 060 set 900MhzTX $_cli_result

action 070 cli command "config t" pattern "#"

action 080 cli command "event manager environment 900MhzTX $900MhzTX" pattern "#"

action 090 cli command "exit" pattern "#"

action 100 cli command "exit" pattern "#"

Thanks,

Tim

Labels:
0 Helpful
7 Replies 7

Joe Clarke
Cisco Employee
Cisco Employee

‎11-26-2013 09:38 AM

This looks wrong.  Perhaps you mean:

action 050 regexp "wlanTxRate=([0-9\.]+)" $_cli_result match txrate

action 060 set 900MhzTX $txrate

! Here you need to disconnect from the radio before you can configure anything on the router

action XXX cli command "config t"

...

0 Helpful

tproeber
Level 1
Level 1
In response to Joe Clarke

‎11-26-2013 09:43 AM

Thanks!  I'm zeroing in on the solution!

Is the "match txrate" part of the command --or a note by you?


0 Helpful

Joe Clarke
Cisco Employee
Cisco Employee
In response to tproeber

‎11-26-2013 09:44 AM

Part of the command.

0 Helpful

tproeber
Level 1
Level 1
In response to tproeber

‎11-26-2013 09:46 AM

Sorry, I see the txrate is the var.

Tim

0 Helpful

tproeber
Level 1
Level 1
In response to tproeber

‎11-26-2013 10:18 AM

The Applet works but gets an error after successfully working:

event manager environment 900_TX 240

event manager directory user policy "flash:/"

event manager applet Radio-Reader

event timer watchdog time 10

action 010 cli command "enable"

action 020 cli command "ssh -l ubnt 192.168.2.11" pattern "assword:"

action 030 cli command "fly2the*" pattern "#"

action 040 cli command "mca-status" pattern "#"

action 050 regexp "wlanTxRate=([0-9]+)" "$_cli_result" match txrate

action 070 cli command "exit" pattern "#"

action 080 cli command "config t" pattern "#"

action 090 cli command "event manager environment 900_TX $txrate" pattern "#"

action 100 cli command "exit" pattern "#"

action 110 cli command "exit" pattern "#"

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : 2901_Rig_1>

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : 2901_Rig_1>enable

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : 2901_Rig_1#

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : 2901_Rig_1#ssh -l ubnt 192.168.2.11

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : CTL : cli_close called.

*Nov 26 12:05:58 UTC:

*Nov 26 12:05:58 UTC: tty is now going through its death sequence

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : Password:

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : fly2the*

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT :

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT :

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : BusyBox v1.11.2 (2013-05-28 17:52:06 EEST) built-in shell (ash)

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : Enter 'help' for a list of built-in commands.

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT :

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : XM.v5.5.6#

*Nov 26 12:05:58 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : mca-status

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : mca-status

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : deviceName=2.4_AP.11,deviceId=DC:9F:DB:6A:A2:17,firmwareVersion=XM.ar7240.v5.5.6.17762.130528.1755,platform=Rocket M2,deviceIp=192.168.2.11

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT :

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : apMac=DC:9F:DB:6A:A2:17

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : wlanOpmode=ap

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : wlanConnections=3

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : wlanUptime=1563423

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : essid=2400

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : freq=2429

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : signal=-40

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : noise=-89

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : ccq=983

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : uptime=1563423

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : loadavg=0

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : memTotal=62012

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : memFree=42976

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : memBuffers=2340

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : ackTimeout=24

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : distance=0

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : lanIpAddress=0.0.0.0

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : CTL : 20+ lines read from cli, debug output truncated

*Nov 26 12:05:59 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : exit

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : exit

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT :

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : [Connection to 192.168.2.11 closed by foreign host]

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : 2901_Rig_1#

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : config t

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : config t

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : Enter configuration commands, one per line.  End with CNTL/Z.

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : 2901_Rig_1(config)#

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : event manager environment 900_TX 240

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : event manager environment 900_TX 240

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : 2901_Rig_1(config)#

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : exit

*Nov 26 12:06:00 UTC: %SYS-5-CONFIG_I: Configured from console by  on vty3 (EEM:Radio-Reader)

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : exit

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : OUT : 2901_Rig_1#

*Nov 26 12:06:00 UTC: %HA_EM-6-LOG: Radio-Reader : DEBUG(cli_lib) : : IN  : exit

2901_Rig_1#

2901_Rig_1#

2901_Rig_1#

2901_Rig_1#term no mon

2901_Rig_1#

2901_Rig_1#

2901_Rig_1#

2901_Rig_1#un all

All possible debugging has been turned off

2901_Rig_1#

2901_Rig_1#

2901_Rig_1#sho eve man his eve

No.  Job Id Proc Status   Time of Event            Event Type        Name

1    24     Actv abort    Tue Nov26 12:04:48 2013  timer watchdog    applet: Radio-Reader

2    25     Actv abort    Tue Nov26 12:04:58 2013  timer watchdog    applet: Radio-Reader

3    26     Actv abort    Tue Nov26 12:05:08 2013  timer watchdog    applet: Radio-Reader

4    27     Actv abort    Tue Nov26 12:05:18 2013  timer watchdog    applet: Radio-Reader

5    28     Actv abort    Tue Nov26 12:05:28 2013  timer watchdog    applet: Radio-Reader

6    29     Actv abort    Tue Nov26 12:05:38 2013  timer watchdog    applet: Radio-Reader

7    30     Actv abort    Tue Nov26 12:05:48 2013  timer watchdog    applet: Radio-Reader

8    31     Actv abort    Tue Nov26 12:05:58 2013  timer watchdog    applet: Radio-Reader

9    32     Actv abort    Tue Nov26 12:06:08 2013  timer watchdog    applet: Radio-Reader

10   33     Actv abort    Tue Nov26 12:06:18 2013  timer watchdog    applet: Radio-Reader

2901_Rig_1#

Thanks,

Tim

0 Helpful

Joe Clarke
Cisco Employee
Cisco Employee
In response to tproeber

‎11-26-2013 10:50 AM

What error?  The only issue I see is that after you disconnect from your radio, you no longer need to use "pattern" with your CLI commands.  The default prompt of the device will be auto-matched.

0 Helpful

tproeber
Level 1
Level 1
In response to Joe Clarke

‎11-26-2013 12:37 PM

Yes, it was just the last "#". 

I think I'm on my way now.

Thanks!

Tim

0 Helpful
Customers Also Viewed These Support Documents