Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

is it possible to create two scripts?

Is it possible this way if I'm making two script? Thanks.

Script 1

For this log:

Apr 24 07:40:01.884 MNL: %LINK-3-UPDOWN: Interface Cellular0/2/0, changed state

to down

ROUTER(config)#event manager applet cell1

ROUTER(config-applet)# event syslog pattern "Interface Cellular0/2/0, changed state to down"

ROUTER(config-applet)# action 1.0 cli command "enable"

ROUTER(config-applet)# action 1.1 cli cmmand "configure term"

ROUTER(config-applet)# action 1.2 cli command "interface Cellular0/2/0"

ROUTER(config-applet)# action 1.3 cli command "no shut"

ROUTER(config-applet)#

Script 2

For this log:

Apr 25 11:17:49.881 MNL: %CELLWAN-2-MODEM_DOWN: Modem in HWIC slot 0/2 is DOWN

ROUTER(config)#event manager applet cell2

ROUTER(config-applet)# event syslog pattern "Modem in HWIC slot 0/2 is DOWN"

ROUTER(config-applet)# action 1.0 cli command "enable"

ROUTER(config-applet)# action 1.1 cli cmmand "reload at 19:00"

ROUTER(config-applet)#

5 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

is it possible to create two scripts?

These will work.  You can have them both configured at once.  However, the reload at is strange.  Is that the only way to recover?  Are you okay with waiting for a specific time to reload?

Cisco Employee

is it possible to create two scripts?

You could use a regexp to do this:

action 001 cli command "enable"

action 002 cli command "show clock"

action 003 regexp "([0-9]+):[0-9]:[0-9]" $_cli_result match hour

action 004 if $hour ge 17

action 005  reload

action 006 end

Cisco Employee

is it possible to create two scripts?

The regexp line extracts the hour portion of the time and the if lines compare that value to 17 (5pm) and 6 (6 am) respectively.  If the hour is greater than or equal to 17 or less than or equal to 6 (numerically) then the reload action will be invoked.

Cisco Employee

is it possible to create two scripts?

event manager applet mode-down

event syslog pattern "Modem in HWIC slot 0/2 is DOWN"

action 1.0 mail from user@company.com to user@company.com server 10.1.1.1 subject "Modem down" body "$_syslog_msg"

Cisco Employee

is it possible to create two scripts?

No.  Not given these scenarios.

event manager applet cell3

description "TEST ONLY"

event syslog pattern "Modem in HWIC slot 0/0 is DOWN"

action 0.5 set timed_reload 0

action 1.0 cli command "enable"

action 1.1 cli command "show clock"

action 1.2 regexp "([0-9]+):[0-9]+:[0-9]+" "$_cli_result" match hour

action 1.3 if $hour ge 18

action 1.4  reload

action 1.9 else

action 2.0  set timed_reload 1

action 2.1 end

action 2.2 if $hour lt 6

action 2.4  reload

action 2.8 else

action 2.9  set timed_reload 1

action 3.0 end

action 3.1 if $timed_reload eq 1

action 3.2  cli command "config t"

action 3.3  cli command "event manager applet reload-at-seven"

action 3.4  cli command "event timer cron cron-entry $q 0 19 * * *$q"

action 3.5  cli command "action 1.0 reload"

action 3.6  cli command "end"

action 3.7 end

62 REPLIES
Cisco Employee

is it possible to create two scripts?

These will work.  You can have them both configured at once.  However, the reload at is strange.  Is that the only way to recover?  Are you okay with waiting for a specific time to reload?

New Member

is it possible to create two scripts?

It's the most convenient time to reload since our client business hours end at 17:00 or 5PM. So i don't want to put the connection down.

Is there as script that could identify when the time comes when the interface or HWIC modem will be down at 19:00 to 0600 and then reload it right away? So i don't have to wait 17:00.

Cisco Employee

is it possible to create two scripts?

You could use a regexp to do this:

action 001 cli command "enable"

action 002 cli command "show clock"

action 003 regexp "([0-9]+):[0-9]:[0-9]" $_cli_result match hour

action 004 if $hour ge 17

action 005  reload

action 006 end

New Member

is it possible to create two scripts?

Wow, i'll try it and i'll let you know. Thanks so much on this. But is this right below?

ROUTER(config)#event manager applet cell2

ROUTER(config-applet)# event syslog pattern "Modem in HWIC slot 0/2 is DOWN"

ROUTER(config-applet)# action 1.0 cli command "enable"

ROUTER(config-applet)# action 1.1 cli command "show clock"

ROUTER(config-applet)# action 1.2 regexp "([0-9]+):[0-9]:[0-9]" $_cli_result match hour

ROUTER(config-applet)# action 1.3 if $hour ge 17

ROUTER(config-applet)# action 1.4 reload

ROUTER(config-applet)# action 1.5 end

Cisco Employee

is it possible to create two scripts?

Yes, but perhaps you want to do:

action 1.6 if $hour le 6

action 1.7  reload

action 1.8 end

And this will only work if the message comes in at that time.  It won't handle the case where the message comes in during business hours.  You would still want to add your reload at line in that case.

New Member

is it possible to create two scripts?

Sorry that i'm being persistent. I'm new at this.

Question, can you help me understand these scripts? the bold phrases.

ROUTER(config-applet)# action 1.2 regexp "([0-9]+):[0-9]:[0-9]" $_cli_result match hour

ROUTER(config-applet)# action 1.3 if $hour ge 17

ROUTER(config-applet)# action 1.4 reload

ROUTER(config-applet)# action 1.5 end

ROUTER(config-applet)# action 1.6 if $hour le 6

ROUTER(config-applet)# action 1.7  reload

ROUTER(config-applet)# action 1.8 end

Appreciate it a lot!

Cisco Employee

is it possible to create two scripts?

The regexp line extracts the hour portion of the time and the if lines compare that value to 17 (5pm) and 6 (6 am) respectively.  If the hour is greater than or equal to 17 or less than or equal to 6 (numerically) then the reload action will be invoked.

New Member

is it possible to create two scripts?

Thank you so much for the assistance. Appreciate it!

New Member

is it possible to create two scripts?

hi joseph, i think the script is not working. i can't see any activity working based on the debug logs. thanks

Cisco Employee

is it possible to create two scripts?

Without seeing what you're seeing, I don't know what to tell you.  I'm honestly not even sure what the script looks like at this point.

New Member

is it possible to create two scripts?

here's what the script looks like

event manager session cli username "jvi01131990"

event manager applet cell1

description "TEST ONLY"

event syslog pattern "Interface Cellular0/0/0, changed state to down"

action 1.0 cli command "enable"

action 1.1 cli command "test cellular 0/0/0 modem-power-cycle"

event manager applet cell2

description "TEST ONLY"

event syslog pattern "Modem in HWIC slot 0/0 is DOWN"

action 1.0 cli command "enable"

action 1.1 cli command "show clock"

action 1.2 regexp "([0-9]+):[0-9]+:[0-9]+" "$_cli_result" match hour

action 1.3 if $hour ge 19

action 1.4  reload

action 1.5 end

action 1.6 if $hour le 6

action 1.7  reload

Cisco Employee

is it possible to create two scripts?

When one of these syslog messages is generated, what do you see in your debug output?  What does "show event manager history event" show?

New Member

is it possible to create two scripts?

to run cell1 manually, its successful, but not with cell2

PHILAM-COT-BR01#sh event manager history events

No.  Job Id Proc Status   Time of Event            Event Type         Name

1    1      Actv success  Mon Oct 7 13:12:01 2013  none               applet: cell1

CELL1

Oct  7 13:11:49.177 MNL: %SYS-5-CONFIG_I: Configured from console by jvi01131990 on vty0 (10.49.135.135)

Oct  7 13:12:01.293 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : CTL : cli_open called.

Oct  7 13:12:01.297 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : OUT : Reload scheduled for 20:00:00 MNL Mon Oct 7 2013 (in 6 hours and 47 minutes) by jvi01131

990 on vty0 (10.49.135.135)

Oct  7 13:12:01.297 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : OUT : Reload reason: Reload Command

Oct  7 13:12:01.297 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : OUT : PHILAM-COT-BR01>

Oct  7 13:12:01.301 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : IN  : PHILAM-COT-BR01>enable

Oct  7 13:12:01.613 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : OUT : PHILAM-COT-BR01#

Oct  7 13:12:01.613 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : IN  : PHILAM-COT-BR01#test cellular 0/0/0 modem-power-cycle

Oct  7 13:12:10.925 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : OUT : Cellular

Modem in HWIC slot 0/0 is still in reset, we recommend to re-execute this cmd after 60 seconds

Oct  7 13:12:10.925 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : OUT : PHILAM-COT-BR01#

Oct  7 13:12:10.925 MNL: %HA_EM-6-LOG: cell1 : DEBUG(cli_lib) : : CTL : cli_close called.

CELL2

Oct  7 13:16:53.137 MNL: %HA_EM-6-FMPD_EEM_CONFIG: cell2: Missing "end" action in conditional block

Oct  7 13:16:53.137 MNL: %SYS-5-CONFIG_I: Configured from console by jvi01131990

on vty0 (10.49.135.135)

Cisco Employee

is it possible to create two scripts?

Cell1 appears to be working.  In cell2, add:

action 1.8 end

That will take care of the error you see there.

New Member

is it possible to create two scripts?

On the underlined logs below, i can see now that the script is working on the 2 downtime instances but there's no indication that the reload command works.

Oct  7 09:09:33.086 MNL: %CELLWAN-2-MODEM_DOWN: Modem in HWIC slot 0/0 is DOWN

Oct  7 09:09:49.674 MNL: %LINK-5-CHANGED: Interface Cellular0/0/0, changed state

to reset

Oct  7 09:09:52.926 MNL: %CELLWAN-2-MODEM_UP: Modem in HWIC slot 0/0 is now UP

Oct  7 09:09:54.674 MNL: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state

to down

Oct  7 09:10:14.718 MNL: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state

to up

Oct  8 08:29:28.113 MNL: %CELLWAN-2-MODEM_DOWN: Modem in HWIC slot 0/0 is DOWN

ROUTER#sh event manager history events

No.  Job Id Proc Status   Time of Event            Event Type         Name

1    1      Actv success  Mon Oct 7 09:09:33 2013  syslog             applet: cell2

2    2      Actv success  Tue Oct 8 08:29:28 2013  syslog             applet: cell2

Oct  8 09:14:14.948 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : CTL : cli_open called.

Oct  8 09:14:14.952 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01>

Oct  8 09:14:14.952 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01>enable

Oct  8 09:14:15.264 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01#

Oct  8 09:14:15.264 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01#show clock

Oct  8 09:14:15.276 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : 09:14:15.264 MNL Tue Oct 8 2013

Oct  8 09:14:15.276 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01#

Oct  8 09:14:15.276 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : CTL : cli_close called.

Also HWIC slot 0/0 keeps and always be down. How to prevent this?

Thank you so much.

Cisco Employee

is it possible to create two scripts?

The reload will only be invoked if the time is between 19:00 and 06:00.  The current time is 09:14.  So the router will not reload.  In terms of the HWIC, you don't do anything in your applet to bring it back up.  If there are commands that need to be run, add them to your cell2 applet.

New Member

is it possible to create two scripts?

is it still works even if it doesn't show up in sh logs? normally reload will take 3-5mins, but logs shows HWIC slot 0/0 is UP after a split second. (in bold)

Oct  7 09:09:33.086 MNL: %CELLWAN-2-MODEM_DOWN: Modem in HWIC slot 0/0 is DOWN

Oct  7 09:09:49.674 MNL: %LINK-5-CHANGED: Interface Cellular0/0/0, changed state

to reset

Oct  7 09:09:52.926 MNL: %CELLWAN-2-MODEM_UP: Modem in HWIC slot 0/0 is now UP

Oct  7 09:09:54.674 MNL: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state

to down

Oct  7 09:10:14.718 MNL: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state

to up

Oct  8 08:29:28.113 MNL: %CELLWAN-2-MODEM_DOWN: Modem in HWIC slot 0/0 is DOWN

Cisco Employee

is it possible to create two scripts?

I don't really understand what the flow from a hardware standpoint should be.  All I can tel you is what I see from the applet commands.  The cell1 applet runs the test command (what it should do, I don't know, but it is running).  The cell2 applet checks the time and reloads the whole router if the time is within a specific window.  That should work, too, if the time is right.

New Member

is it possible to create two scripts?

Sorry for being persistent, but for this scenario below, the HWIC did state it was down as of 00:05, but i think the applet didn't works, it supposed to reload between 19:00-6:00. So i reloaded it manually after i've noticed it at 8:43.

Oct  9 00:05:58.018 MNL: %CELLWAN-2-MODEM_DOWN: Modem in HWIC slot 0/0 is DOWN

Oct  9 08:43:05.044 MNL: %SYS-5-SCHEDULED_RELOAD: Reload requested for 20:00:00 MNL Wed Oct 9 2013 at 08:43:03 MNL Wed Oct 9 2013 by jvi01131990 on vty0 (10.49.

135.135). Reload Reason: Reload Command.

Oct  9 08:46:47.592 MNL: %SYS-5-CONFIG_I: Configured from console by jvi01131990 on vty0 (10.49.135.135)

Oct  9 08:46:56.184 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : CTL : cli_open called.

Oct  9 08:46:56.192 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : Reload scheduled for 20:00:00 MNL Wed Oct 9 2013 (in 11 hours and 13 minutes) by jvi0113

1990 on vty0 (10.49.135.135)

Oct  9 08:46:56.192 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : Reload reason: Reload Command

Oct  9 08:46:56.192 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01>

Oct  9 08:46:56.192 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01>enable

Oct  9 08:46:56.504 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01#

Oct  9 08:46:56.504 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01#show clock

Oct  9 08:46:56.516 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : 08:46:56.508 MNL Wed Oct 9 2013

Oct  9 08:46:56.516 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01#

Oct  9 08:46:56.516 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : CTL : cli_close called.

Oct  9 08:48:40.104 MNL: %HA_EM-4-FMPD_NO_EVENT: No event configured for applet cell2

Oct  9 08:48:40.104 MNL: %SYS-5-CONFIG_I: Configured from console by jvi01131990 on vty0 (10.49.135.135)

Cisco Employee

is it possible to create two scripts?

This debug is from 08:46, though.  It doesn't show what happened at midnight.

New Member

is it possible to create two scripts?

I've noticed that the syslog below sometimes occur between 6AM - 6PM, so which means the event applet below will not take effect. question, how can i do a script that whenever the syslog pattern occur b/n 6AM-6PM i could set it up to reload automatically at 7PM. thanks

event manager applet cell2

description "TEST ONLY"

event syslog pattern "Modem in HWIC slot 0/0 is DOWN"

action 1.0 cli command "enable"

action 1.1 cli command "show clock"

action 1.2 regexp "([0-9]+):[0-9]+:[0-9]+" "$_cli_result" match hour

action 1.3 if $hour ge 18

action 1.4 reload

action 1.5 end

action 1.6 if $hour le 6

action 1.7 reload

action 1.8 end

Cisco Employee

is it possible to create two scripts?

Have this applet configure another applet that triggers a reload at 19:00.  That is, add actions like:

event manager environment q "

!

action 1.7 cli command "config t"

action 1.8 cli command "event manager applet reload-at-seven"

action 1.9 cli command "event timer cron cron-entry $q 0 19 * * *$q"

action 2.0 cli command "action 1.0 reload"

action 2.1 cli command "end"

action 2.2 end

Same thing starting at action 1.4.

New Member

is it possible to create two scripts?

is this correct?

event manager applet cell3

description "TEST ONLY"

event syslog pattern "Modem in HWIC slot 0/0 is DOWN"

action 1.0 cli command "enable"

action 1.1 cli command "show clock"

action 1.2 regexp "([0-9]+):[0-9]+:[0-9]+" "$_cli_result" match hour

action 1.3 if $hour ge 18

action 1.4 reload

action 1.5 end

action 1.6 if $hour le 6

action 1.7 reload

action 1.8 end

action 1.9 cli command "config t"

action 2.0 cli command "event manager applet reload-at-seven"

action 2.1 cli command "event timer cron cron-entry $q 0 19 * * *$q"

action 2.2 cli command "action 1.0 reload"

action 2.3 cli command "end"

action 2.4 end

Cisco Employee

is it possible to create two scripts?

No.  The action numbers I listed were what I meant.  Meaning what I provided was designed to replace action 1.7 on.  Note: you'll also have to replace actions 1.4 and 1.5 with the same list of items I did starting at action 1.7.

New Member

is it possible to create two scripts?

is this right?

the script must have this 2 scenario below. thanks.

  • 1st scenario should be it will reload automatically if syslog appears from 6PM to 6AM.
  • 2nd scenario should be it will reload at 7PM if syslog appears from 6AM to 6PM.

event manager applet cell3

description "TEST ONLY"

event syslog pattern "Modem in HWIC slot 0/0 is DOWN"

action 1.0 cli command "enable"

action 1.1 cli command "show clock"

action 1.2 regexp "([0-9]+):[0-9]+:[0-9]+" "$_cli_result" match hour

action 1.3 if $hour ge 18

action 1.4 cli command "config t"

action 1.5 cli command "event manager applet reload-at-seven"

action 1.6 cli command "event timer cron cron-entry $q 0 19 * * *$q"

action 1.7 cli command "action 1.0 reload"

action 1.8 cli command "end"

action 1.9 end

action 2.0 if $hour le 6

action 2.1 cli command "config t"

action 2.2 cli command "event manager applet reload-at-seven"

action 2.3 cli command "event timer cron cron-entry $q 0 19 * * *$q"

action 2.4 cli command "action 1.0 reload"

action 2.5 cli command "end"

action 2.6 end

Cisco Employee

is it possible to create two scripts?

No.  Not given these scenarios.

event manager applet cell3

description "TEST ONLY"

event syslog pattern "Modem in HWIC slot 0/0 is DOWN"

action 0.5 set timed_reload 0

action 1.0 cli command "enable"

action 1.1 cli command "show clock"

action 1.2 regexp "([0-9]+):[0-9]+:[0-9]+" "$_cli_result" match hour

action 1.3 if $hour ge 18

action 1.4  reload

action 1.9 else

action 2.0  set timed_reload 1

action 2.1 end

action 2.2 if $hour lt 6

action 2.4  reload

action 2.8 else

action 2.9  set timed_reload 1

action 3.0 end

action 3.1 if $timed_reload eq 1

action 3.2  cli command "config t"

action 3.3  cli command "event manager applet reload-at-seven"

action 3.4  cli command "event timer cron cron-entry $q 0 19 * * *$q"

action 3.5  cli command "action 1.0 reload"

action 3.6  cli command "end"

action 3.7 end

New Member

is it possible to create two scripts?

Hi Joseph, i've run the script and see if it works the way 2 scenarios should be. Thank you very much

Nov 12 15:19:04.828 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : CTL : cli_open called.

Nov 12 15:19:04.828 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01>

Nov 12 15:19:04.828 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01>enable

Nov 12 15:19:05.140 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01#

Nov 12 15:19:05.140 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01#show clock

Nov 12 15:19:05.152 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : 15:19:05.140 MNL Tue Nov 12 2013

Nov 12 15:19:05.152 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01#

Nov 12 15:19:05.152 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01#config t

Nov 12 15:19:05.464 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : Enter configuration commands, one per line.  End with CNTL/Z.

Nov 12 15:19:05.464 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01(config)#

Nov 12 15:19:05.464 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01(config)#event manager applet reload-at-seven

Nov 12 15:19:05.776 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01(config-applet)#

Nov 12 15:19:05.776 MNL: %HA_EM-3-FMPD_UNKNOWN_ENV: fh_parse_var: could not find environment variable: q

Nov 12 15:19:05.776 MNL: %HA_EM-3-FMPD_ERROR: Error executing applet cell2 statement 3.4

Nov 12 15:19:05.776 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : CTL : cli_close called.

PHILAM-ANT-BR01#sh event manager history events

No.  Job Id Proc Status   Time of Event            Event Type         Name

4    4      Actv success  Tue Nov12 15:19:04 2013  none               applet: cell2

New Member

is it possible to create two scripts?

Nov 12 15:19:05.464 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : IN  : PHILAM-ANT-BR01(config)#event manager applet reload-at-seven

Nov 12 15:19:05.776 MNL: %HA_EM-6-LOG: cell2 : DEBUG(cli_lib) : : OUT : PHILAM-ANT-BR01(config-applet)#

Nov 12 15:19:05.776 MNL: %HA_EM-3-FMPD_UNKNOWN_ENV: fh_parse_var: could not find environment variable: q

Nov 12 15:19:05.776 MNL: %HA_EM-3-FMPD_ERROR: Error executing applet cell2 statement 3.4

Cisco Employee

is it possible to create two scripts?

You need to make sure the following is configured on your device:

event manager environment q "

5800
Views
13
Helpful
62
Replies