Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

LDAP acceptance

I would like to configure LDAP acceptance. The mail server is Scalix. I've found some information in Scalix for LDAP:

swa.ldap.1.type=system
swa.ldap.1.server=mail.test.com
swa.ldap.1.port=389
swa.ldap.1.baseDN=o=scalix
swa.ldap.1.displayName.resourceID=addressbooksearch_title_system
swa.ldap.1.displayName.resourceLabel=System Directory
swa.ldap.1.authType=none
swa.ldap.1.filter=(|(&(cn=%s*)(mail=*))(&(sn=%s*)(mail=*))(&(gn=%s*)(mail=*))(mail=%s*)(&(omalias=%s*)(mail=*)))
swa.ldap.1.addressSearchLimit=100
swa.ldap.1.search.1.header=true
swa.ldap.1.search.1.type=name
swa.ldap.1.search.1.name.resourceID=addressbooksearch_label_name
swa.ldap.1.search.1.name.resourceLabel=Name
swa.ldap.1.search.1.dirAttribute=omcn
swa.ldap.1.search.2.header=true
swa.ldap.1.search.2.type=email
swa.ldap.1.search.2.name.resourceID=addressbooksearch_label_email
swa.ldap.1.search.2.name.resourceLabel=Email Address
swa.ldap.1.search.2.dirAttribute=rfc822Mailbox
swa.ldap.1.search.3.header=true
swa.ldap.1.search.3.type=
swa.ldap.1.search.3.name.resourceID=addressbooksearch_label_phone
swa.ldap.1.search.3.name.resourceLabel=Phone
swa.ldap.1.search.3.dirAttribute=telephoneNumber
swa.ldap.1.search.4.header=
swa.ldap.1.search.4.type=
swa.ldap.1.search.4.name.resourceID=
swa.ldap.1.search.4.name.resourceLabel=Fax Phone
swa.ldap.1.search.4.dirAttribute=facsimileTelephoneNumber
swa.ldap.1.search.5.header=
swa.ldap.1.search.5.type=
swa.ldap.1.search.5.name.resourceID=
swa.ldap.1.search.5.name.resourceLabel=Mobile Phone
swa.ldap.1.search.5.dirAttribute=mobileTelephoneNumber
swa.ldap.1.search.6.header=
swa.ldap.1.search.6.type=
swa.ldap.1.search.6.name.resourceID=
swa.ldap.1.search.6.name.resourceLabel=Pager Phone
swa.ldap.1.search.6.dirAttribute=pagerTelephoneNumber
swa.ldap.2.type=personal
swa.ldap.2.server=mail.test.com
swa.ldap.2.port=389
swa.ldap.2.baseDN=o=MyContacts
swa.ldap.2.displayName.resourceID=addressbooksearch_title_personal
swa.ldap.2.displayName.resourceLabel=Personal Contacts
swa.ldap.2.authType=simple
swa.ldap.2.bindDN=rfc822mailbox=%u
swa.ldap.2.filter=(|(&(cn=%s*)(|(mail=*)(304=4)))(&(sn=%s*)(mail=*))(&(gn=%s*)(mail=*))(mail=%s*)(&(omalias=%s*)(mail=*)))

So what are the parameters for LDAP acceptance according to the information above?

3 REPLIES
New Member

Re: LDAP acceptance

Can you have more information be exported for this user? From scanning over the output below, I cannot identify where a user's email address would be except for this one value:

swa.ldap.1.search.2.name.resourceLabel=Email Address



I would like to configure LDAP acceptance. The mail server is Scalix. I've found some information in Scalix for LDAP:

swa.ldap.1.type=system
swa.ldap.1.server=mail.test.com
swa.ldap.1.port=389
swa.ldap.1.baseDN=o=scalix
swa.ldap.1.displayName.resourceID=addressbooksearch_title_system
swa.ldap.1.displayName.resourceLabel=System Directory
swa.ldap.1.authType=none
swa.ldap.1.filter=(|(&(cn=%s*)(mail=*))(&(sn=%s*)(mail=*))(&(gn=%s*)(mail=*))(mail=%s*)(&(omalias=%s*)(mail=*)))
swa.ldap.1.addressSearchLimit=100
swa.ldap.1.search.1.header=true
swa.ldap.1.search.1.type=name
swa.ldap.1.search.1.name.resourceID=addressbooksearch_label_name
swa.ldap.1.search.1.name.resourceLabel=Name
swa.ldap.1.search.1.dirAttribute=omcn
swa.ldap.1.search.2.header=true
swa.ldap.1.search.2.type=email
swa.ldap.1.search.2.name.resourceID=addressbooksearch_label_email
swa.ldap.1.search.2.name.resourceLabel=Email Address
swa.ldap.1.search.2.dirAttribute=rfc822Mailbox
swa.ldap.1.search.3.header=true
swa.ldap.1.search.3.type=
swa.ldap.1.search.3.name.resourceID=addressbooksearch_label_phone
swa.ldap.1.search.3.name.resourceLabel=Phone
swa.ldap.1.search.3.dirAttribute=telephoneNumber
swa.ldap.1.search.4.header=
swa.ldap.1.search.4.type=
swa.ldap.1.search.4.name.resourceID=
swa.ldap.1.search.4.name.resourceLabel=Fax Phone
swa.ldap.1.search.4.dirAttribute=facsimileTelephoneNumber
swa.ldap.1.search.5.header=
swa.ldap.1.search.5.type=
swa.ldap.1.search.5.name.resourceID=
swa.ldap.1.search.5.name.resourceLabel=Mobile Phone
swa.ldap.1.search.5.dirAttribute=mobileTelephoneNumber
swa.ldap.1.search.6.header=
swa.ldap.1.search.6.type=
swa.ldap.1.search.6.name.resourceID=
swa.ldap.1.search.6.name.resourceLabel=Pager Phone
swa.ldap.1.search.6.dirAttribute=pagerTelephoneNumber
swa.ldap.2.type=personal
swa.ldap.2.server=mail.test.com
swa.ldap.2.port=389
swa.ldap.2.baseDN=o=MyContacts
swa.ldap.2.displayName.resourceID=addressbooksearch_title_personal
swa.ldap.2.displayName.resourceLabel=Personal Contacts
swa.ldap.2.authType=simple
swa.ldap.2.bindDN=rfc822mailbox=%u
swa.ldap.2.filter=(|(&(cn=%s*)(|(mail=*)(304=4)))(&(sn=%s*)(mail=*))(&(gn=%s*)(mail=*))(mail=%s*)(&(omalias=%s*)(mail=*)))

So what are the parameters for LDAP acceptance according to the information above?

New Member

Re: LDAP acceptance

Did yu ever get this to work? I'd like to get this working also! If you did, what was needed?

regards,
oldO

New Member

Re: LDAP acceptance

I don't have any new info on my side, but if the information provided was a generic form, then the ldap accept query string should look like this:

For example,

if the setting is:

swa.ldap.1.search.2.name.resourceLabel= jsmith@company.com


the ldap accept query string should be:

(swa.ldap.1.search.2.name.resourceLabel={a})

But an example from a real user would be better. The above is just a guess.



Can you have more information be exported for this user?  From scanning over the output below, I cannot identify where a user's email address would be except for this one value:

swa.ldap.1.search.2.name.resourceLabel=Email Address

151
Views
0
Helpful
3
Replies