ASA 5510 and static route

[mnetworks]

Hi all.

This is my first setup of a Cisco ASA box.

I'm having a lot of problems with use of static route

If I make a PING from the ASA box, I get a replay.

But if the ping comes from a computer, I keep getting: Deny inbound icmp src inside:XXX des inside:YYY (Type 8, code 0)

I have tried to make a NAT rule for this, but I cannot make a role src inside, drs inside

Can any one help me whit this?

Thanks?

Best regards.

Stig B.

[acomiskey]

No need for a nat rule or static route for this...just add the following

icmp permit any inside

[mnetworks]

hi,

Sorry, doesn?t work.

ERROR: entry for address/mask = 0.0.0.0/0.0.0.0 exists

Thanks..

[acomiskey]

I think I misunderstood, what are you trying to ping from the inside computer? Another computer on the inside on a different network, or the ASA itself? Looks like you are trying to ping from machine on inside to another machine inside. This traffic is being routed to inside of ASA and it is denying it as by default it will not allow traffic to go in and out of same interface. You will need to add the "same-security-traffic permit intra-interface" command to allow that to happen.

[mnetworks]

Thanks a lot.

Now I dont get the deny inbound error.

But I get a: Portmap translation creation failed for icmp src inside:xxx dst inside: xxx (type 8, code 0)

Do I need NAT for that?

[acomiskey]

try...

global (inside) 1 interface

[mnetworks]

Thank you so much for your time and Knowles

But, it didn?t do the trick.

Do you have another idea?

[acomiskey]

What error are you getting now? No translation group found...? Add the following...

static (inside,inside) netmask 255.255.255.255

= the computer you are trying to ping

[acomiskey]

So to review you should have...

same-security-traffic permit intra-interface

global (inside) 1 interface

static (inside,inside) netmask 255.255.255.255

You could also do this for the whole network instead of just

static (inside,inside) netmask

[mnetworks]

Hi,

?same-security-traffic permit intra-interface? - Worked, but gave a new error.

(portmap translation creation faild for icmp src inside:XXX dst inside:YYY (type 8, code 0))

?global (inside) 1 interface? - Didn?t help on the new error

static (inside,inside) netmask - I have tried fowling:

static (inside,inside) netmask

static (inside,inside) netmask

static (inside,inside) netmask

But none of this works, and I still have the portmap problem?.

[hoogen_82]

Could you let us know about your scenario. I could possibly give you sample configuration which would work for your setup.

-Hoogen

[mnetworks]

Hi,

My Cisco ASA 5510 box is going to be a new HQ firewall/VPN ? (HQN)

On the old HQ box (Cisco VPN3000), all of the VPN lines for the EU network is connected. ? (HQO)

At HQN there is a old Cisco Router whit a connection to HQO.

I?m going to move all of the VPN lines one-by-one, but keep the hole network up at the same time.

Before a start moving client computers and servers to the new HQN box (ASA), I want to be able to route traffic from ASA to the VPN3000 at HQN

A copy of my conf, see the Attachment

At The new HQ:

ASA: 192.168.163.1

Router: 192.168.163.30

My problem is that fowling doesn?t work:

route LAN 192.126.60.0 255.255.255.0 192.168.163.30 1

route LAN 172.16.3.0 255.255.255.0 192.168.163.30 1

route LAN 10.3.26.0 255.255.255.0 192.168.163.30 1

route LAN 10.2.0.0 255.255.255.0 192.168.163.30 1

route LAN 10.0.5.0 255.255.255.0 192.168.163.30 1

route LAN 10.0.4.0 255.255.252.0 192.168.163.30 1

route LAN 192.168.168.0 255.255.255.0 192.168.163.30 1

I hope you understand me, because my English is not the best.

Thanks..

[acomiskey]

Sorry, should have checked, this should do it.

no global (LAN) 1 interface

global (LAN) 200 interface

[mnetworks]

Hi,

The error message is gone now, but I don?t get any replay back.

I know the server I?m pinging is there, because when I?m using the 192.168.163.30 as GW, there is no problem.

[srue]

nat (inside) 1 0.0.0.0 0.0.0.0

global (outside) 1 interface