Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

ASA 5510 v8.3, problem with static NAT

Hi,

I have problem to create static NAT between public IP address range (ie. 222.222.222.2 - 222.222.222.6) and private IP address range (192.168.101.2 - 192.168.101.6). When I try to ping the PC (192.168.101.2) in my private network from the public network (ping 222.222.222.2) or vice versa nothing happend. The "debug nat" command shows the following error message: nat: untranslation - outside0:222.222.222.2/0 to inside0/3:192.168.101.2/0.

Here is my configuration:


ASA Version 8.3(1)
!
hostname Firewall
enable password ZcWMFYW8y4cSHoCz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
nameif outside0
security-level 100
ip address 222.222.222.221 255.255.255.192          (ip address is an example address)
!
interface Ethernet0/1
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
nameif inside0/3
security-level 100
no ip address
!
interface Ethernet0/3.10
description VLAN 10
vlan 10
nameif inside_netwok1
security-level 100
ip address 192.168.101.1 255.255.255.0
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
!
boot system disk0:/asa831-k8.bin
ftp mode passive
object network MAPPED_INSIDE
range 192.168.101.2 192.168.101.6
object network MAPPED_OUTSIDE
range 222.222.222.2 222.222.222.6
access-list Traffic_in extended permit ip any 222 222.222.2.255.255.255.248
access-list Traffic_in extended permit ip any 192.168.101.0 255.255.255.0

pager lines 24
mtu inside_netwok1 1500
mtu outside0 1500
mtu inside0/3 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
!
object network MAPPED_INSIDE
nat (inside0/3,outside0) static MAPPED_OUTSIDE
object network MAPPED_JULKINEN
nat (outside0,inside0/3) static MAPPED_INSIDE
access-group Traffic_in in interface outside0

timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 60
ssh version 2
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username jklp password q0MTHZ/Tiy/UXjqC encrypted privilege 15
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
  message-length maximum client auto
  message-length maximum 512
policy-map global_policy
class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect ip-options
  inspect netbios
  inspect rsh
  inspect rtsp
  inspect skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect tftp
  inspect sip
  inspect xdmcp
!
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
  no active
  destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
  destination address email callhome@cisco.com
  destination transport-method http
  subscribe-to-alert-group diagnostic
  subscribe-to-alert-group environment
  subscribe-to-alert-group inventory periodic monthly
  subscribe-to-alert-group configuration periodic monthly
  subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:87409b9bc0a2eedf2f98857d07991d71
: end

Thanks,

Tuomas

  • Firewalling
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: ASA 5510 v8.3, problem with static NAT

Your config is right, there is something else that is happening.

Try packet tracer

packet-tracer input outside icmp host 8 0 host <222.222.222.4

And see what the ASA will do with the packet.

Also use

capture capin interface inside0/3 match icmp host host 192.168.101.4

capture capout interface outside match icmp host host 222.222.222.4

sh cap capin

show cap capout

to capture packets and see if they are sent.

I hope it helps.

PK

5 REPLIES
Silver

Re: ASA 5510 v8.3, problem with static NAT

Please remove the following lines  as there is no need for them:

access-list Traffic_in extended permit ip any 222 222.222.2.255.255.255.248

object network MAPPED_JULKINEN
nat (outside0,inside0/3) static MAPPED_INSIDE

(actually removing the network object should also remove the nat statement)

Once you have done this, you may have to do "clear local-host" , "clear xlate" .

Then try again.

New Member

Re: ASA 5510 v8.3, problem with static NAT

Thank you for the answer! Unfornately it did not help me. I removed unnecessary lines from my configurartion but the NAT not works. Below is my current configuration:


: Saved
:
ASA Version 8.3(1)
!
hostname Jyvas-P
enable password ZcWMFYW8y4cSHoCz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
nameif outside0
security-level 100
ip address 222.222.222.194 255.255.255.192    (ip address is an example address)
!
interface Ethernet0/1
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
nameif inside0/3
security-level 100
no ip address
!
interface Ethernet0/3.10
description TAC-yhteydet
vlan 10
nameif TAC-verkko
security-level 100
ip address 192.168.101.1 255.255.255.0
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
!
boot system disk0:/asa831-k8.bin
ftp mode passive
object network MAPPED_INSIDE
range 192.168.101.2 192.168.101.6
object network MAPPED_OUTSIDE
range 222.222.222.222 222.222.222.226
access-list Traffic_in extended permit ip any 192.168.101.0 255.255.255.0
pager lines 24
mtu outside0 1500
mtu inside0/3 1500
mtu TAC-verkko 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
!
object network MAPPED_INSIDE
nat (inside0/3,outside0) static MAPPED_OUTSIDE
access-group Traffic_in in interface outside0
route outside0 0.0.0.0 0.0.0.0 222.222.222.193 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 60
ssh version 2
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username jklp password q0MTHZ/Tiy/UXjqC encrypted privilege 15
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
  message-length maximum client auto
  message-length maximum 512
policy-map global_policy
class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect ip-options
  inspect netbios
  inspect rsh
  inspect rtsp
  inspect skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect tftp
  inspect sip
  inspect xdmcp
!
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
  no active
  destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
  destination address email callhome@cisco.com
  destination transport-method http
  subscribe-to-alert-group diagnostic
  subscribe-to-alert-group environment
  subscribe-to-alert-group inventory periodic monthly
  subscribe-to-alert-group configuration periodic monthly
  subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:5d9d41b39442c2e7c793ca4f7e724e1a
: end

Thanks,

-Tuomas

Cisco Employee

Re: ASA 5510 v8.3, problem with static NAT

Your config is right, there is something else that is happening.

Try packet tracer

packet-tracer input outside icmp host 8 0 host <222.222.222.4

And see what the ASA will do with the packet.

Also use

capture capin interface inside0/3 match icmp host host 192.168.101.4

capture capout interface outside match icmp host host 222.222.222.4

sh cap capin

show cap capout

to capture packets and see if they are sent.

I hope it helps.

PK

New Member

Re: ASA 5510 v8.3, problem with static NAT

Hi,

Thanks for your help! I used the command "packet-tracer input outside icmp host 8 0 host  <222.222.222.4" and I saw that there was some implicit rule which denied the traffic. I have configured same security-level on each interface and the traffic between same security level interfaces is denied.

There was also another mistake in command " nat (inside0/3,outside0) static MAPPED_OUTSIDE" because I use subinterface "TAC-verkko". So the right command is " nat (TAC-verkko,outside0) static MAPPED_OUTSIDE.

- Tuomas

Cisco Employee

Re: ASA 5510 v8.3, problem with static NAT

That is good news!

PK

1358
Views
0
Helpful
5
Replies
This widget could not be displayed.