Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

ASA 8.4 failover interface testing issue

Team

From ASA 5520 we tested the interface failover it not working even the interface are getting monitor .

primary is active.

Manually we shut the outside interface of the primary device configuration is getting reflecting in secondary as outside interface shut. Interface failover not happen.

ii All the interface are getting monitor when we gave command sh failover. even though when we shut outside interface failove not happening.

kindly tell us how to do the interface failover in ASA 8.4 version.

Regards

Sudharsan.R

1 ACCEPTED SOLUTION

Accepted Solutions
Red

ASA 8.4 failover interface testing issue

Do you have the interfaces as monitored interface, can you provide the output of "show run failover" and "shwo failover"

Thanks,

Varun

Thanks, Varun Rao Security Team, Cisco TAC
3 REPLIES
Red

ASA 8.4 failover interface testing issue

Do you have the interfaces as monitored interface, can you provide the output of "show run failover" and "shwo failover"

Thanks,

Varun

Thanks, Varun Rao Security Team, Cisco TAC

ASA 8.4 failover interface testing issue

hi varun here is the output

xxxxx-asa-01/pri/act# sh failover

Failover On

Failover unit Primary

Failover LAN Interface: xover GigabitEthernet0/3 (up)

Unit Poll frequency 1 seconds, holdtime 3 seconds

Interface Poll frequency 3 seconds, holdtime 15 seconds

Interface Policy 1

Monitored Interfaces 6 of 160 maximum

Version: Ours 8.4(2)8, Mate 8.4(2)8

Last Failover at: 16:39:29 UTC Jan 4 2012

        This host: Primary - Active

                Active time: 5511130 (sec)

                slot 0: ASA5520 hw/sw rev (2.0/8.4(2)8) status (Up Sys)

                  Interface CW-Internet-delivery (62.208.154.20): Normal (Monitored)

                  Interface WAN-transit (192.168.40.4): Normal (Monitored)

                  Interface Platform-Management (10.13.48.138): Normal (Monitored)

                  Interface Colo (10.128.128.193): Normal (Monitored)

                  Interface Blue-Coat-outer (10.128.128.65): Normal (Monitored)

                  Interface Blue-Coat-inner (10.128.128.33): Normal (Monitored)

                slot 1: ASA-SSM-4GE hw/sw rev (1.0/1.0(0)10) status (Up)

        Other host: Secondary - Standby Ready

                Active time: 249370 (sec)

                slot 0: ASA5520 hw/sw rev (2.0/8.4(2)8) status (Up Sys)

                  Interface CW-Internet-delivery (62.208.154.21): Normal (Monitored)

                  Interface WAN-transit (192.168.40.5): Normal (Monitored)

                  Interface Platform-Management (10.13.48.139): Normal (Monitored)

                  Interface Colo (10.128.128.194): Normal (Monitored)

                  Interface Blue-Coat-outer (10.128.128.66): Normal (Monitored)

                  Interface Blue-Coat-inner (10.128.128.34): Normal (Monitored)

                slot 1: ASA-SSM-4GE hw/sw rev (1.0/1.0(0)10) status (Up)

Stateful Failover Logical Update Statistics

        Link : xover GigabitEthernet0/3 (up)

        Stateful Obj    xmit       xerr       rcv        rerr

        General         6286980409 0          3594275    0

        sys cmd         734957     0          734957     0

        up time         0          0          0          0

        RPC services    0          0          0          0

        TCP conn        4884205    0          6947       0

        UDP conn        11249789   0          8428       0

        ARP tbl         6270111331 0          2843941    0

        Xlate_Timeout   0          0          0          0

        IPv6 ND tbl     0          0          0          0

        VPN IKEv1 SA    0          0          0          0

        VPN IKEv1 P2    0          0          0          0

        VPN IKEv2 SA    76         0          0          0

        VPN IKEv2 P2    12         0          0          0

        VPN CTCP upd    0          0          0          0

        VPN SDI upd     0          0          0          0

        VPN DHCP upd    0          0          0          0

        SIP Session     0          0          0          0

        Route Session   0          0          0          0

        User-Identity   39         0          2          0

        Logical Update Queue Information

                        Cur     Max     Total

        Recv Q:         0       250     3601771

        Xmit Q:         0       1485    6293432921

xxxxx-asa-01/pri/act#

xxx-asa-01/pri/act# sh runn failover

failover

failover lan unit primary

failover lan interface xover GigabitEthernet0/3

failover polltime unit 1 holdtime 3

failover polltime interface 3 holdtime 15

failover link xover GigabitEthernet0/3

failover interface ip xover 10.99.99.1 255.255.255.252 standby 10.99.99.2

xxxxxx-asa-01/pri/act#

Re: ASA 8.4 failover interface testing issue

please see the output of the device and reply still we face the same issue when we shut the bluecoat outer interface failover not happening.

Regards

Sudharsan.R

641
Views
0
Helpful
3
Replies
CreatePlease to create content