07-13-2012 02:26 AM - edited 03-11-2019 04:30 PM
I have a Cisco ASA 5505, version 7.2(4) which I am trying to configure. Previously I had access to the firewall via ASDM, but since erasing the old configuration and starting on a new one, I can no longer access it. I have entered the following commands:
crypto key generate rsa modulus 1024
http server enable
http192.168.1.0 255.255.255.0 inside
aaa authentication ssh console LOCAL
ssh 192.168.1.0 255.255.255.0 inside
aaa authentication http console LOCAL
username supervisor password Password123 privilege 15
I can ping the inside address (192.168.1.1)
When I try to open the ASDM, I always get the message, "Cannot launch Device Manager from 192.168.1.1")
ASDM Launcher version: 1.5(49)
ASDM .bin image in flash: 524
Does anyone have any suggestions? Other than the ASDM, the firewall seems to be working as configured. It is set up with a static external address and internal DHCP, which is working just fine.
Solved! Go to Solution.
07-13-2012 02:40 AM
07-13-2012 06:28 AM
this is a "layer 8" error
07-13-2012 02:40 AM
hi,
insert these line:
http server enable
http
Regards
V
07-13-2012 02:53 AM
Isn't that what this is?:
http server enable
http 192.168.1.0 255.255.255.0 inside
I've already done that (see my original post), and the IP address on my computer is in the 192.168.1.x range.
07-13-2012 03:01 AM
sorry
I had not seen the first few lines,
ok,
if you try to connect whith a browser to https://192.168.1.1/admin
what do you see?
07-13-2012 03:04 AM
Hi,
From the CLI issue the command: show run asdm
The output could be something like this:
asdm image disk0:/asdm-641.bin
You should see a command that defines the ASDM software file used. When configuring it, make sure its compatible with the actual ASA software. Though I think the ASA will give an error message if the version arent compatible.
- Jouni
07-13-2012 03:07 AM
Hi Judy
Please could you post the following:
ciscoasa# sh asdm image
Device Manager image file, disk0:/asdm-645.bin
ciscoasa# sh version
Cisco Adaptive Security Appliance Software Version 8.2(2)
Device Manager Version 6.4(5)
Compiled on Mon 11-Jan-10 14:19 by builders
System image file is "disk0:/asa822-k8.bin"
Config file at boot was "startup-config"
Regards Craig
07-13-2012 05:55 AM
v.errante - trying to access https://192.16.1.1/admin gives me a webpage timeout
Other information as requested by Jouni and Craig:
FIREWALL(config)# show run asdm
asdm image disk0:/asdm-524.bin
no asdm history enable
FIREWALL(config)# sh asdm image
Device Manager image file, disk0:/asdm-524.bin
FIREWALL(config)# sh version
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
Config file at boot was "startup-config"
07-13-2012 06:16 AM
please attach your config
07-13-2012 06:19 AM
Ok, now I feel dumb. Looked through the running-config carefully and found this:
http 192.16.1.0 255.255.255.0 inside
Sticky "8" Key strikes again....
07-13-2012 06:28 AM
this is a "layer 8" error
07-13-2012 10:23 AM
Hahaha, touché. Sorry for wasting everyone's time.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide