Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

ASDM Launch

I have a Cisco ASA 5505, version 7.2(4) which I am trying to configure.  Previously I had access to the firewall via ASDM, but since erasing the old configuration and starting on a new one, I can no longer access it.  I have entered the following commands:

crypto key generate rsa modulus 1024

http server enable

http192.168.1.0 255.255.255.0 inside

aaa authentication ssh console LOCAL

ssh 192.168.1.0 255.255.255.0 inside

aaa authentication http console LOCAL
username supervisor password Password123 privilege 15

I can ping the inside address (192.168.1.1)
When I try to open the ASDM, I always get the message, "Cannot launch Device Manager from 192.168.1.1")

ASDM Launcher version: 1.5(49)
ASDM .bin image in flash: 524

Does anyone have any suggestions?  Other than the ASDM, the firewall seems to be working as configured.  It is set up with a static external address and internal DHCP, which is working just fine.

Everyone's tags (2)
2 ACCEPTED SOLUTIONS

Accepted Solutions
New Member

ASDM Launch

hi,

insert these line:

http server enable

http

Regards

V

New Member

ASDM Launch

this is a "layer 8" error

10 REPLIES
New Member

ASDM Launch

hi,

insert these line:

http server enable

http

Regards

V

New Member

ASDM Launch

Isn't that what this is?:

http server enable

http 192.168.1.0 255.255.255.0 inside

I've already done that (see my original post), and the IP address on my computer is in the 192.168.1.x range.

New Member

ASDM Launch

sorry

I had not seen the first few lines,

ok,

if you try to connect whith a browser to https://192.168.1.1/admin

what do you see?

Super Bronze

ASDM Launch

Hi,

From the CLI issue the command: show run asdm

The output could be something like this:

asdm image disk0:/asdm-641.bin

You should see a command that defines the ASDM software file used. When configuring it, make sure its compatible with the actual ASA software. Though I think the ASA will give an error message if the version arent compatible.

- Jouni

New Member

ASDM Launch

Hi Judy

Please could you post the following:

ciscoasa# sh asdm image
Device Manager image file, disk0:/asdm-645.bin

ciscoasa# sh version

Cisco Adaptive Security Appliance Software Version 8.2(2)
Device Manager Version 6.4(5)

Compiled on Mon 11-Jan-10 14:19 by builders
System image file is "disk0:/asa822-k8.bin"
Config file at boot was "startup-config"

Regards Craig

New Member

ASDM Launch

v.errante -  trying to access https://192.16.1.1/admin gives me a webpage timeout

Other information as requested by Jouni and Craig:

FIREWALL(config)# show run asdm

asdm image disk0:/asdm-524.bin

no asdm history enable

FIREWALL(config)# sh asdm image

Device Manager image file, disk0:/asdm-524.bin

FIREWALL(config)# sh version

Cisco Adaptive Security Appliance Software Version 7.2(4)

Device Manager Version 5.2(4)

Compiled on Sun 06-Apr-08 13:39 by builders

System image file is "disk0:/asa724-k8.bin"

Config file at boot was "startup-config"

New Member

ASDM Launch

please attach your config

New Member

ASDM Launch

Ok, now I feel dumb.   Looked through the running-config carefully and found this:

http 192.16.1.0 255.255.255.0 inside

Sticky "8" Key strikes again....

New Member

ASDM Launch

this is a "layer 8" error

New Member

ASDM Launch

Hahaha, touché.   Sorry for wasting everyone's time.

753
Views
0
Helpful
10
Replies
CreatePlease to create content