Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cannot Ping local Subnet from ASA

Hi

Can someone please check this config,

We have this asa5510 as our default gateway (10.0.0.1)

We also have a 2821 router running cme with two sub interfaces (10.0.0.3 & 192.168.100.1)

I have added a route on the asa to 192.168.100.0 but cannot ping to 192.168.100.1 from clients on the 10.0.0.0 network although I can from the asa itself.

Can you see what is causing this?

Thanks,

Chris

8 REPLIES

Re: Cannot Ping local Subnet from ASA

asa config seems fine

IN 2821 router do you have a route back to reach 10.0.0.0/24 subnet or a default route pointing to asa inside interface

i.e

ip route 10.0.0.0 255.255.255.0 10.0.0.1

or

ip route 0.0.0.0 0.0.0.0 10.0.0.1

if you do have above example already in 2821, can you gather asa logs while trying to ping 192.168.100.0/24 hosts from 10.0.0.0/24 network and post the logs.

Rgds

Jorge

New Member

Re: Cannot Ping local Subnet from ASA

Hi,

I tried adding ip route 0.0.0.0 0.0.0.0 10.0.0.1 but still wouldn't work. Would it still need this route even though the 2821 has one of it's interfaces in the 10.0.0.0/24 network?

When I try and ping from the client 10.0.0.78 to 192.168.100.1 this shows up in the asa log

portmap translation creation failed for icmp src INSIDE:10.0.0.78 dst INSIDE:192.168.100.1 (type 8, code 0)

does anyone have an idea what could be causing this

Thanks,

Chris

New Member

Re: Cannot Ping local Subnet from ASA

I thought it may be to do with the ASA natting traffic to 192.168.100.0 so I added

access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 192.168.100.0 255.255.255.0

It still doesn't ping but I get a different error on the ASA:

No translation group found for icmp src INSIDE:10.0.0.78 dst INSIDE:192.168.100.1 (type 8, code 0)

Re: Cannot Ping local Subnet from ASA

Sorry for late reply..

invert the acl

remove

no access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 192.168.100.0 255.255.255.0

rewrite statement with

access-list NONAT extended permit ip 192.168.100.0 255.255.255.0 10.0.0.0 255.255.255.0

then try from 10.10.10.78 pinging to any host on the 192.168.100.0/24 net

New Member

Re: Cannot Ping local Subnet from ASA

Hi Chris

add these commands and it will work fine with you

same-security-traffic permit intra-interface

static (inside,inside) 10.0.0.0 10.0.0.0 netmask 255.0.0.0 norandomseq nailed

static (inside,inside) 192.168.100.0 192.168.100.0 netmask 255.255.255.0 norandomseq nailed

sysopt noproxyarp inside

failover timeout -1

When you put these commands it will work fine.

Thanks,

New Member

Re: Cannot Ping local Subnet from ASA

Thanks for your help, would it be possible to explain what these commands are doing as well.

New Member

Re: Cannot Ping local Subnet from ASA

Dear Chris

refer to the below link and you can find the answer:

http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Security&topic=Firewalling&topicID=.ee6e1fa&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc1d776

also you can have another solution if you put the default gateway for the users as the CME router (10.0.0.3) and point a default route on the router to the 10.0.0.1 (ip route 0.0.0.0 0.0.0.0 10.0.0.1).

thanks,

New Member

Re: Cannot Ping local Subnet from ASA

Thanks for your help.

Would this affect performance if all packets had to go through the router first rather than straight out of the ASA?

Also I have Site to Site VPN's set up that I wish to connect to the CME system e.g. 192.168.3.0 is a remote site. What steps would I need to take for this network to see the internal 192.168.100.0 network?

Regards,

Chris

458
Views
0
Helpful
8
Replies