Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco ASA 5510-K8 License upgrade to enable Eth 0/3

Hi There,


I have Cisco ASA 5510-K8 where I can't use Eth 0/3. Below is the Sh ver output which says Eth 0/3 is not licensed. It has base license at the moment and I believe that we need to have security plus license to enable Eth 0/3 but would like to confirm the exact license as Cisco has many options with different types.

Cisco ASA 5510# sh version

Cisco Adaptive Security Appliance Software Version 7.0(6)

Device Manager Version 5.0(6)

Hardware:   ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash AT49LW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

                             Boot microcode   : CNlite-MC-Boot-Cisco-1.2

                             SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03

                             IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.04

0: Ext: Ethernet0/0         : address is 000a.b89c.eca0, irq 9

1: Ext: Ethernet0/1         : address is 000a.b89c.eca1, irq 9

2: Ext: Ethernet0/2         : address is 000a.b89c.eca2, irq 9

3: Ext: Not licensed        : irq 9

4: Ext: Management0/0       : address is 000a.b89c.ec9f, irq 11

5: Int: Not licensed        : irq 11

6: Int: Not licensed        : irq 5

Licensed features for this platform:

Maximum Physical Interfaces : 4

Maximum VLANs               : 10

Inside Hosts                : Unlimited

Failover                    : Disabled

VPN-DES                     : Enabled

VPN-3DES-AES                : Enabled

Security Contexts           : 0

GTP/GPRS                    : Disabled

VPN Peers                   : 50

This platform has a Base license.

Thanks in Advance.

Prabjeet

1 ACCEPTED SOLUTION

Accepted Solutions

Cisco ASA 5510-K8 License upgrade to enable Eth 0/3

Hi,

Cisco ASA 5510 Security Plus license (provides Active/Active and Active/Standby high availability, increased session and VLAN capacities, and additional Ethernet interfaces)

ASA5510-SEC-PL

For more information about Core and Security Networking follow my website at http://laguiadelnetworking.com

Any question contact me at jcarvaja@laguiadelnetworking.com

Cheers,

Julio Carvajal Segura

Looking for some Networking Assistance? Contact me directly at jcarvaja@laguiadelnetworking.com I will fix your problem ASAP. Cheers, Julio Carvajal Segura http://laguiadelnetworking.com
4 REPLIES

Cisco ASA 5510-K8 License upgrade to enable Eth 0/3

Hi,

Cisco ASA 5510 Security Plus license (provides Active/Active and Active/Standby high availability, increased session and VLAN capacities, and additional Ethernet interfaces)

ASA5510-SEC-PL

For more information about Core and Security Networking follow my website at http://laguiadelnetworking.com

Any question contact me at jcarvaja@laguiadelnetworking.com

Cheers,

Julio Carvajal Segura

Looking for some Networking Assistance? Contact me directly at jcarvaja@laguiadelnetworking.com I will fix your problem ASAP. Cheers, Julio Carvajal Segura http://laguiadelnetworking.com
Silver

Cisco ASA 5510-K8 License upgrade to enable Eth 0/3

Security Plus license will also enable Gigabit speed on Eth0/0 and Eth0/1.

New Member

Cisco ASA 5510-K8 License upgrade to enable Eth 0/3

Thanks for your help

New Member

Cisco ASA 5510-K8 License upgrade to enable Eth 0/3

Thanks

321
Views
0
Helpful
4
Replies