Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

Cisco ASA 5525-X alarm led on

Hello,

I have installed 3 cisco asa 5525-x. One of these has the alarm led on. I take a look in the troubleshooting guide and I found to run show environment and

show controller pci.

Everything seems ok with this command.

The firewall is working but I would like to understand if there is some problem (hardware or software).

OS version is 9.

Can someone help me in suggesting other command to run?

Thanks

Alessandra

Everyone's tags (3)
12 REPLIES
New Member

Re: Cisco ASA 5525-X alarm led on

Hi,

I have the same problem too. But from my understanding

you should have dual power supplies. If you have just one, install the redundant power supply and test.

and check what type of PCI card you installed. blank module or something with cable?

I did these and then the alarm went off.

Thanks

Alaguraja.K

New Member

Re: Cisco ASA 5525-X alarm led on

I am having the same problem on a 5512-X... any suggestions? Thx

New Member

Hi all,  Me too with 5512X.

Hi all,

 

 

Me too with 5512X. any suggestions? possible bug or cosmetic problem?

New Member

Cisco ASA 5525-X alarm led on

sh controller pci

  PCI Evaluation Log:

  ---------------------------------------------------------------------------

    1.) System is not fully operational - The PCI device with vendor ID: 0x1000 (LSI) device ID: 0x0a05 (Accelerator) could not be found in the system.

  PCI Bus:Device.Function (hex): 00:00.0 Vendor ID: 0x8086 Device ID: 0xd130

  ---------------------------------------------------------------------------

    PCI Configuration Space (hex):

    0x00: 86 80 30 d1 00 00 10 00 11 00 00 06 10 00 00 00

    0x10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    0x20: 00 00 00 00 00 00 00 00 00 00 00 00 5b 10 61 0d

    0x30: 00 00 00 00 40 00 00

New Member

Cisco ASA 5525-X alarm led on

I am having the the same issue with a Cisco ASA 5512-X.

The alarm LED is solid amber. The commands "show environment" and "show controller pci" are all ok.

We also have two Cisco ASA 5515-X in active/active multiple-context mode, their alarm LED is off.

Any suggestions?

New Member

Cisco ASA 5525-X alarm led on

Hi,

This may be because of IPS issue.

Please check:

sh module ips det

Thanks

New Member

Re: Cisco ASA 5525-X alarm led on

I don't know if this is a question for me. But in my case we don't have IPS, if I run the command "show module module ips detect" I get the following output:

HOSTNAME(config)# sh module ips details

Getting details from the Service Module, please wait...

Unable to read details from module ips

Card Type:          Unknown

Model:              N/A

Hardware version:   N/A

Serial Number:      ABCDEFGHIIDDENMYME

Firmware version:   N/A

Software version:  

MAC Address Range:  a80a.0aa1.4146 to a80a.0da1.4146

Data Plane Status:  Not Applicable

Status:             Unresponsive   No Image Present

License:            IPS Module  Disabled  perpetual

New Member

Re: Cisco ASA 5525-X alarm led on

HI

If this device is in production, please arrange a downtime and unplug the power and wait for 30 sec, then power on the device again.

If this works then there may be was a false alarm was on.

Please share the update.

Thanks

New Member

Re: Cisco ASA 5525-X alarm led on

That did not fix the problem. This is a brand new ASA laying on my desk serveral times. It has been shutdown multiple times to store it for the evening. The alarm LED is still there.

New Member

Re: Cisco ASA 5525-X alarm led on

 Hello !
I had the same problem on my ASA 5525-X: 

 

1.) System is not fully operational - The PCI device with vendor ID: 0x1000 (LSI) device ID: 0x0a05 (Accelerator) could not be found in the system.


Help please!

New Member

try installing an ASA-IC-B

try installing an ASA-IC-B-BLANK (the one with a regex ribbon cable).  Had a similar problem and that was the solution.

New Member

Re: Cisco ASA 5525-X alarm led on

Hello !
I had the same problem on my ASA 5525-X
Help please!

 

1.) System is not fully operational - The PCI device with vendor ID: 0x1000 (LSI) device ID: 0x0a05 (Accelerator) could not be found in the system.

5825
Views
0
Helpful
12
Replies
CreatePlease to create content