Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Step-by-Step Configuration and Troubleshooting Best Practices for the NGFW, NGIPS and AMP Technologies A Visual Guide to the Cisco Firepower Threat Defense (FTD)
Community Member

cisco wlc

WLCNG Boot Loader Version 1.0.20 (Built on Jan  9 2014 at 19:02:44 by cisco)
Board Revision 0.0 (SN: PSZ18031QCM, Type: AIR-CT2504-K9) (P)

Verifying boot loader integrity... OK.

OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)
CPU Cores:  4
DRAM:  1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1, octeth2, octeth3
  ' - Active interface
  E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
 - Model: 1GB CompactFlash Card Firm: CF B612J Ser#: A191103295A10b8D1J3m
 - Type: Hard Disk
 - Capacity: 977.4 MB = 0.9 GB (2001888 x 512)


Press <ESC> now to access the Boot Menu...

 

 

 

 

 

============================================================
 Boot Loader Menu
============================================================

 1. Run primary image (Bad image type) - Active
 2. Run backup image (Image not found)
 3. Change active boot image
 4. Clear configuration
 5. Format FLASH Drive
 6. Manually update images

------------------------------------------------------------
Enter selection: 6
Launching...
Launching images...
init started: BusyBox v1.6.0 (2009-02-03 04:56:32 EST) multi-call binary
Mount failed for selinuxfs on /selinux:  No such file or directory
starting pid 655, tty '': '/etc/init.d/rcS'
Use DHCP for ip configuration (Y/n)? Y
Sending DHCP request . . .
DHCP client bound to address 192.168.2.2
Enter TFTP server IP address[(192.168.2.1 )]: 192.168.2.55

!!! WARNING updating using .aes or unapproved files will disable this unit !!!

Do you want to update RTOS (y/N)? y

Do you want to update Primary Or Secondary Image (P/s)? P

Enter filename for RTOS update: AIR-CT2500-K9-7-6-120-0.aes
RTOS update Done

Enter filename for FP update: AIR-CT2500-K9-7-6-120-0.aes
FP update Done
Do you want to update an AP image (y/N)?
AP Images Not Updated
Done.  Restarting...
Restarting system.


WLCNG Boot Loader Version 1.0.20 (Built on Jan  9 2014 at 19:02:44 by cisco)
Board Revision 0.0 (SN: PSZ18031QCM, Type: AIR-CT2504-K9) (W)

Verifying boot loader integrity... OK.

OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)
CPU Cores:  4
DRAM:  1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1, octeth2, octeth3
  ' - Active interface
  E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
 - Model: 1GB CompactFlash Card Firm: CF B612J Ser#: A191103295A10b8D1J3m
 - Type: Hard Disk
 - Capacity: 977.4 MB = 0.9 GB (2001888 x 512)


Press <ESC> now to access the Boot Menu...

Loading primary image (Bad image type)
100%

146388020 bytes read
WARNING: Data loaded outside of the reserved load area, memory corruption may occur.
WARNING: Please refer to the bootloader memory map documentation for more information.

 

plz give the solution this problem

1 REPLY
Hall of Fame Super Blue

Contact TAC and RMA the

Contact TAC and RMA the appliance. 

61
Views
0
Helpful
1
Replies
CreatePlease to create content