Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Password Recovery on PIX 501 and 515

Im trying to do a password recovery on a PIX,i downloaded the password recovery software np63 and renamed it to np63.bin

i keep following these steps..

monitor>interface 0

0: i8255X @ PCI(bus:0 dev:13 irq:10)

1: i8255X @ PCI(bus:0 dev:14 irq:7 )

Using 0: i82559 @ PCI(bus:0 dev:13 irq:10), MAC: 0050.54ff.82b9

monitor>address 10.10.10.2

address 10.10.10.2

monitor>server 10.10.10.1

server 10.10.10.1

monitor>file np63.bin

file np63.bin

monitor>ping 10.10.10.1

Sending 5, 100-byte 0xf8d3 ICMP Echoes to 10.10.10.1, timeout is 4 seconds:

!!!!!

Success rate is 100 percent (5/5)

monitor>tftp

tftp np52.bin@10.10.10.1

But i keep getting the following error message,any ideas...

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

1 REPLY

Re: Password Recovery on PIX 501 and 515

Your file is np63.bin - but the tftp request is for file np52.bin??

"monitor>file np63.bin "

"monitor>tftp

tftp np52.bin@10.10.10.1 "

try using

"tftp np63.bin@10.10.10.1 "

HTH.

394
Views
0
Helpful
1
Replies