cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
772
Views
0
Helpful
1
Replies

Password Recovery on PIX 501 and 515

mojalefa1
Level 1
Level 1

Im trying to do a password recovery on a PIX,i downloaded the password recovery software np63 and renamed it to np63.bin

i keep following these steps..

monitor>interface 0

0: i8255X @ PCI(bus:0 dev:13 irq:10)

1: i8255X @ PCI(bus:0 dev:14 irq:7 )

Using 0: i82559 @ PCI(bus:0 dev:13 irq:10), MAC: 0050.54ff.82b9

monitor>address 10.10.10.2

address 10.10.10.2

monitor>server 10.10.10.1

server 10.10.10.1

monitor>file np63.bin

file np63.bin

monitor>ping 10.10.10.1

Sending 5, 100-byte 0xf8d3 ICMP Echoes to 10.10.10.1, timeout is 4 seconds:

!!!!!

Success rate is 100 percent (5/5)

monitor>tftp

tftp np52.bin@10.10.10.1

But i keep getting the following error message,any ideas...

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

5/21/2008 13:58 :Timeout error sending np63.bin to 10.10.10.2, 0 bytes

1 Reply 1

andrew.prince
Level 10
Level 10

Your file is np63.bin - but the tftp request is for file np52.bin??

"monitor>file np63.bin "

"monitor>tftp

tftp np52.bin@10.10.10.1 "

try using

"tftp np63.bin@10.10.10.1 "

HTH.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card