cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
653
Views
0
Helpful
9
Replies

PIX 515 boot in loop

hlecalon
Level 1
Level 1

after a upgrade to v7.2.3

device is in a loop boot due to a bad config file.

how can i erase my config as i can't loginto my device ??

9 Replies 9

andrew.prince
Level 10
Level 10

hello,

actually i can't log into my device because it crashes while proceding my config file :

WARNING: The trustpoint will not be set for crypto map entry 'vers_partenaires3'

> , sequence number 84, as there was already a pre-shared-key specified for a peer

> in this crypto map entry. In order to initiate Isakmp tunnels using certificate

> s, the crypto map must indicate wh

> Thread Name: pix_flash_config_thread (Old pc 0x0085eefd ebp 0x02605f18)

> vector 0x00000003 (breakpoint)

> edi 0x02605cd0

> esi 0x00003a99

> ebp 0x02605c84

> esp 0x02605c78

> ebx 0x0168fe50

> edx 0x00000007

> ecx 0x0168fe88

> eax 0x27ba7755

> error code n/a

> eip 0x0107f79c

> cs 0x00000008

> eflags 0x00000046

> CR2 0x00000000

>

> Cisco PIX Security Appliance Software Version 7.2(3)

>

> Compiled on Wed 15-Aug-07 16:08 by builders

i dont' kwown how to fix it !!!

If you have followed the password recovery procedure - you will know that you are actually interupting the boot process, BEFORE the device actually loads the config file.

I suggest you read the link I posted and try it.

HTH>

hello, thanks for you information about the password recovery procedure, but the actual problem is that my device boots with 7.2.3 version of software and starts to proceed my configfile that was imported from V6.3 and the device crashes while proceding the configfile so that i'm not able to type any command line into it in order to erase my flash of config file. so i was wondering how it was possible to clear flash without being logged into the device.

i have already tried the password recovery procedure, because i hoped that it coul'd help me to clear my config file

Best regards

During the bootup, press the esc key during the first 10 seconds. The boot process will look similar to this:

Cisco Secure PIX Firewall BIOS (4.2) #0: Mon Dec 31 08:34:35 PST 2001

Platform PIX-515E

System Flash=E28F128J3 @ 0xfff00000

Use BREAK or ESC to interrupt flash boot.

Use SPACE to begin flash boot immediately.

Flash boot interrupted.

0: i8255X @ PCI(bus:0 dev:14 irq:10)

1: i8255X @ PCI(bus:0 dev:13 irq:11)

2: i8255X @ PCI(bus:1 dev:0 irq:11)

3: i8255X @ PCI(bus:1 dev:1 irq:10)

4: i8255X @ PCI(bus:1 dev:2 irq:9 )

5: i8255X @ PCI(bus:1 dev:3 irq:5 )

Ethernet auto negotiation timed out.

Ethernet port 1 could not be initialized.

Use ? for help.

monitor>

Now you can follow the password recovery procedure and boot without a config. Once the pix is booted, you can erase your old config by typing: "write erase" or "clear configure all".

hello thanks again for this explication, i managed to clear the password from the pix.

BUT when it'e reboots, il start to load the config file and then crashes so that i can't type any command to clear my config file

Follow the upgrade procedure and load your os via tftp. Once it has loaded, either copy the config OFF of the pix, delete the local copy and reboot, or erase the config using the commands in my previous message.

Please rate if helpful.

Thanks, when i try to apply the upgrade procedure i have this message :

Received 2193408 bytes

Cisco Secure PIX Firewall admin loader (3.0) #0: Tue May 21 08:26:10 PDT 2002

Flash=i28F640J5 @ 0x300

BIOS Flash=AT29C257 @ 0xd8000

An internal assertion check has failed.

Copy the following message exactly as it appears,

along with any visible version strings, and

then call your support representative.

assertion "addr < STRATA_CHIPSIZE" failed: file "../flash/strata.c", line 222

Rebooting....

i'am stuck in it. do ypu have any ideas ?

Hi,

PIX has this problem.

1. It can be possible a hardware problem.

2. Software Image not uploaded or damaged.

----

1. Try to revert back to the old IOS running on the pix.

get the traceback logs from the pix after reload to troubleshoot more.

2. Try to reupload a new image.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: