Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Pix 525 6.3(4) to Pix 535 7.2(4)

We just purchased a refurbished Pix 535 with ver 7.2(4) as a temp. solution until a backorderd ASA5550 arrives.

The Pix 535 will replace our existing Pix 525, which has ver 6.3(4).

I've read through some of the config. coversion documention concerning Interfaces and Fixup protocols.

Our Pix 525 has a very basic config.  We don't do NAT and only have an access-list configured for our Outside interface.

Concerning the NAT.  Will the following statements work on version 7.2(4).  We still do not want to perform any NAT.

nat (inside) 0 155.42.0.0 255.255.0.0 0 0

static (inside,outside) 155.42.0.0 155.42.0.0 netmask 255.255.0.0 0 0

Thanks,

Tom

  • Firewalling
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: Pix 525 6.3(4) to Pix 535 7.2(4)

tffmaguire wrote:

We just purchased a refurbished Pix 535 with ver 7.2(4) as a temp. solution until a backorderd ASA5550 arrives.

The Pix 535 will replace our existing Pix 525, which has ver 6.3(4).

I've read through some of the config. coversion documention concerning Interfaces and Fixup protocols.

Our Pix 525 has a very basic config.  We don't do NAT and only have an access-list configured for our Outside interface.

Concerning the NAT.  Will the following statements work on version 7.2(4).  We still do not want to perform any NAT.

nat (inside) 0 155.42.0.0 255.255.0.0 0 0

static (inside,outside) 155.42.0.0 155.42.0.0 netmask 255.255.0.0 0 0

Thanks,

Tom

Tom

Yes those commands will work on v7.2(4) although they seem to be doing the same thing.

Jon

Cisco are currently donating money to the Haiti earthquake appeal for every rating so please consider rating all helpful posts.

2 REPLIES
Hall of Fame Super Blue

Re: Pix 525 6.3(4) to Pix 535 7.2(4)

tffmaguire wrote:

We just purchased a refurbished Pix 535 with ver 7.2(4) as a temp. solution until a backorderd ASA5550 arrives.

The Pix 535 will replace our existing Pix 525, which has ver 6.3(4).

I've read through some of the config. coversion documention concerning Interfaces and Fixup protocols.

Our Pix 525 has a very basic config.  We don't do NAT and only have an access-list configured for our Outside interface.

Concerning the NAT.  Will the following statements work on version 7.2(4).  We still do not want to perform any NAT.

nat (inside) 0 155.42.0.0 255.255.0.0 0 0

static (inside,outside) 155.42.0.0 155.42.0.0 netmask 255.255.0.0 0 0

Thanks,

Tom

Tom

Yes those commands will work on v7.2(4) although they seem to be doing the same thing.

Jon

Cisco are currently donating money to the Haiti earthquake appeal for every rating so please consider rating all helpful posts.

New Member

Re: Pix 525 6.3(4) to Pix 535 7.2(4)

Thanks Jon.

I haven't work on a firewall in a couple of years, so I wanted to make sure the migration went smoothly.

I always get confused around the NAT syntax.

Again, I appreciate your quick response.

Thanks,

Tom

322
Views
0
Helpful
2
Replies