Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

"admin-context" command not available on FWSM

Hi gurus,

Probably, I have a totally stupid newbie question. I got a new Cisco FWSM and trying to configure from scratch. Looks like command "admin-context" is not available from firewall configuration mode. Is it a licensing problem? Am I in a wrong mode? Thank you!

FW# show ver

FWSM Firewall Version 3.2(5)

Compiled on Mon 10-Mar-08 16:03 by fwsmbld

FW up 16 days 3 hours

Hardware: WS-SVC-FWM-1, 1024 MB RAM, CPU Pentium III 1000 MHz

Flash STI Flash 8.0.0 @ 0xc321, 20MB

0: Int: Not licensed : irq 5

1: Int: Not licensed : irq 7

2: Int: Not licensed : irq 11

The Running Activation Key is not set, using default settings:

Licensed features for this platform:

Maximum Interfaces : 256

Inside Hosts : Unlimited

Failover : Active/Active

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Cut-through Proxy : Enabled

Guards : Enabled

URL Filtering : Enabled

Security Contexts : 2

GTP/GPRS : Disabled

BGP Stub : Disabled

VPN Peers : Unlimited

Serial Number: SAD123602JE

Running Activation Key: 0x00000000

0x00000000 0x00000000 0x00000000

Configuration last modified by enable_15 at 14:46:41.458 UTC Fri Dec 12 2008

config)# ?

------------------------------------------------------------

aaa Enable, disable, or view user authentication,

authorization and accounting

aaa-server Configure a AAA server group or a AAA server

access-group Bind an access-list to an interface to filter traffic

access-list Configure an access control element

alias Administer overlapping addresses with dual NAT

arp Change or view ARP table, set ARP timeout value, view

statistics

asdm Configure Device Manager

auth-prompt Customize authentication challenge, reject or

acceptance prompt

auto-update Configure Auto Update

banner Configure login/session banners

ca Certification authority

<skipped>

url-block Enable URL pending block buffer and long URL support

url-cache Enable/Disable URL caching

url-server Configure a URL filtering server

username Configure user authentication local database

virtual Configure address for authentication virtual servers

vpn-addr-assign Global settings for VPN IP address assignment policy

vpn-sessiondb Configure the VPN Session Manager

vpngroup Configure a policy group for VPN clients

xlate-bypass Enable/Disable xlate bypass

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: "admin-context" command not available on FWSM

Type "sh mode".

If it's says "single" then you are in wrong mode. To change to multiple mode -

http://www.cisco.com/en/US/docs/security/fwsm/fwsm32/configuration/guide/contxt_f.html#wp1051132

Note what happens to the existing config.

If it says "multiple" try entering

"ch sys"

Jon

2 REPLIES
Hall of Fame Super Blue

Re: "admin-context" command not available on FWSM

Type "sh mode".

If it's says "single" then you are in wrong mode. To change to multiple mode -

http://www.cisco.com/en/US/docs/security/fwsm/fwsm32/configuration/guide/contxt_f.html#wp1051132

Note what happens to the existing config.

If it says "multiple" try entering

"ch sys"

Jon

New Member

Re: "admin-context" command not available on FWSM

Thank you!

136
Views
0
Helpful
2
Replies