02-27-2011 11:03 PM - edited 03-11-2019 12:57 PM
Hello support,
we had configure firewall on active standby mode and when i try to reboot secondary device it will reboot by old version of IOS to asa702.bin.
but my actully configured by asa802.bin We have check on firewall that boot file are below.
sh boot
BOOT variable = disk0:/asa802-k8.bin
Current BOOT variable = disk0:/asa802-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
02-27-2011 11:09 PM
Hi,
Could you please paste the output of the following:
sh run boot
sh bootvar
sh disk0:
Regards,
Anisha
02-27-2011 11:59 PM
Dear Anisha,
Thanks for support,
please find below detail as per you post.
#########################################Primary device###############################
PRAsaOne# sh run boot
boot system disk0:/asa802-k8.bin
PRAsaOne# show run bootvar
BOOT variable = disk0:/asa802-k8.bin
Current BOOT variable = disk0:/asa802-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
PRAsaOne# show disk0:
--#-- --length-- -----date/time------ path
64 5511168 Jan 01 2003 00:05:06 asa707-k8.bin
6 8192 Aug 10 2007 18:00:20 crypto_archive
65 6161700 Aug 10 2007 18:12:14 asdm-507.bin
67 14524416 Feb 27 2011 05:23:28 asa802-k8.bin
68 8202240 Nov 01 2007 00:48:58 asa721-k8.bin
69 8192 Nov 26 2009 14:39:28 tmp
70 6889764 Feb 27 2011 05:24:50 asdm-602.bin
2 8192 Oct 31 2009 09:18:24 log
255426560 bytes total (213696512 bytes free)
#########################################Secondary device############################
PRAsaOne#sh run boot
boot system disk0:/asa802-k8.bin
PRAsaOne# sh bootvar
BOOT variable = disk0:/asa802-k8.bin
Current BOOT variable = disk0:/asa802-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
PRAsaOne# show disk0:
--#-- --length-- -----date/time------ path
64 5511168 Jan 01 2003 00:05:24 asa707-k8.bin
6 8192 Aug 10 2007 17:51:56 crypto_archive
65 6161700 Aug 10 2007 18:04:00 asdm-507.bin
67 14524416 Feb 27 2011 13:07:42 asa802-k8.bin
68 6889764 Feb 27 2011 13:10:02 asdm-602.bin
69 8202240 Nov 01 2007 02:20:18 asa721-k8.bin
2 8192 Oct 31 2009 10:18:16 log
70 8192 Nov 26 2009 14:24:10 tmp
255426560 bytes total (213704704 bytes free)
02-28-2011 12:17 AM
Please paste the output of sh ver of the secondary device.
Regards,
Anisha
02-28-2011 01:38 AM
Dear Anisha,
##############sh version##########################
Cisco Adaptive Security Appliance Software Version 8.0(2)
Device Manager Version 6.0(2)
Compiled on Fri 15-Jun-07 19:29 by builders
System image file is "disk0:/asa802-k8.bin"
Config file at boot was "startup-config"
GoaSDCAsaOne up 19 hours 41 mins
failover cluster up 19 hours 53 mins
Hardware: ASA5540, 1024 MB RAM, CPU Pentium 4 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.01
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Ext: GigabitEthernet0/0 : address is 001b.d46e.4718, irq 9
1: Ext: GigabitEthernet0/1 : address is 001b.d46e.4719, irq 9
2: Ext: GigabitEthernet0/2 : address is 001b.d46e.471a, irq 9
3: Ext: GigabitEthernet0/3 : address is 001b.d46e.471b, irq 9
4: Ext: Management0/0 : address is 001b.d46e.4717, irq 11
5: Int: Internal-Data0/0 : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 200
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 5000
WebVPN Peers : 2
Advanced Endpoint Assessment : Disabled
This platform has an ASA 5540 VPN Premium license.
Serial Number: JMX3322L1GK
Running Activation Key: 0x2h3bdd58 0x88390dcd0 0xf123cda4 0x908784a0 0x4dd5ae9f
Configuration register is 0x1
Configuration last modified by enable_15 at 14:35:56.845 UTC Mon Feb 28 2011
02-28-2011 03:20 AM
Hi,
So the ASA is running 8.0.2. since it is on 8.0.2 means it has booted with version 8.0.2.
how did you come to a conclusion that it is booting with previous ASA ver.
Regards,
Anisha
02-28-2011 04:29 AM
Hello anisha,
thanks for support,
we are just Reboot ASA and while its reboot its just go to its previous version of IOS which is available in disk0:
and its try to stabilise with primary.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide