Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Unable to see interface on ASA 5510 Firewall

Hi All,

I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.

Below is the output.

ciscoasa# sh int ip br
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0/0                x.x.x.x           YES CONFIG up                    up
Ethernet0/1                x.x.x.x           YES CONFIG up                    up
Ethernet0/2                unassigned      YES unset  administratively down down
Internal-Control0/0        127.0.1.1       YES unset  up                    up
Internal-Data0/0           unassigned      YES unset  up                    up
Management0/0              192.168.1.1     YES CONFIG up                    up

Please suggest what could be the reason.

Regards

Pankaj

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

Re: Unable to see interface on ASA 5510 Firewall

Are you still running version 7.2.1 or older? These versions had a restriction to 3+1 interfaces in the Base-Version. Starting with 7.22 the limit was removed.

Sent from Cisco Technical Support iPad App


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
8 REPLIES
Hall of Fame Super Silver

Unable to see interface on ASA 5510 Firewall

Most likely it is hardware failure and will require replacement via the TAC (if you have a support contract).

Can you reboot and watch power on self test output from console for any errors?

Unable to see interface on ASA 5510 Firewall

Hi Pankaj,

Try with this command in your ASA

hw-module module 1 reset and check if that solves your problem. Even after that if it not shows then prabably you need to go for a TAC/RMA for the hardware checked.

Please do rate if the given information helps.

By

Karthik

VIP Purple

Re: Unable to see interface on ASA 5510 Firewall

Are you still running version 7.2.1 or older? These versions had a restriction to 3+1 interfaces in the Base-Version. Starting with 7.22 the limit was removed.

Sent from Cisco Technical Support iPad App


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni

Unable to see interface on ASA 5510 Firewall

Hi Bro

I have a strong feeling your Cisco ASA 5510 was purchased with inadequate license i.e. ASA5510-BUN-K9. For this reason, you're ONLY able to use 3 physcial interfaces from the total 4 :-) You should add-on the Security Plus license, and all will be good.

ASA5510-BUN-K9                   ASA 5510 Appliance with SW, 5FE,3DES/AES                                       

ASA5510-SEC-BUN-K9           ASA 5510 Security Plus Appl with SW, HA, 2GE+3FE, 3DES/AES          

P/S: If you think this comment is useful, please do rate them nicely :-) and select the option “This Question is Answered”

Warm regards, Ramraj Sivagnanam Sivajanam Technical Specialist/Service Delivery Manager – Managed Service Department

Re: Unable to see interface on ASA 5510 Firewall

Hi Ramraj,

Even i have the base license for my ASA 5510 which is showing all the 4 interfaces in sh ver. I don't think so license would be an issue. There should be some IOS code bug that needs to be upgraded. If this goes for an OS upgrade it should get resolved.

Its not showing up in sh ver . As Karsten said he might be running on old IOS version.

fy-a# sh ver

Cisco Adaptive Security Appliance Software Version 8.4(4)1

Device Manager Version 6.4(5)

Compiled on Thu 14-Jun-12 11:20 by builders

System image file is "disk0:/asa844-1-k8.bin"

Config file at boot was "startup-config"

fy-a up 1 day 1 hour

Hardware:   ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash M50FW016 @ 0xfff00000, 2048KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

                             Boot microcode   : CN1000-MC-BOOT-2.00

                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03

                             IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.06

                             Number of accelerators: 1

0: Ext: Ethernet0/0         : address is 2c54.2d0c.8f1a, irq 9

1: Ext: Ethernet0/1         : address is 2c54.2d0c.8f1b, irq 9

2: Ext: Ethernet0/2         : address is 2c54.2d0c.8f1c, irq 9

3: Ext: Ethernet0/3         : address is 2c54.2d0c.8f1d, irq 9

4: Ext: Management0/0       : address is 2c54.2d0c.8f1e, irq 11

5: Int: Not used            : irq 11

6: Int: Not used            : irq 5

Licensed features for this platform:

Maximum Physical Interfaces       : Unlimited      perpetual

Maximum VLANs                     : 50             perpetual

Inside Hosts                      : Unlimited      perpetual

Failover                          : Disabled       perpetual

VPN-DES                           : Enabled        perpetual

VPN-3DES-AES                      : Enabled        perpetual

Security Contexts                 : 0              perpetual

GTP/GPRS                          : Disabled       perpetual

AnyConnect Premium Peers          : 2              perpetual

AnyConnect Essentials             : Disabled       perpetual

Other VPN Peers                   : 250            perpetual

Total VPN Peers                   : 250            perpetual

Shared License                    : Disabled       perpetual

AnyConnect for Mobile             : Disabled       perpetual

AnyConnect for Cisco VPN Phone    : Disabled       perpetual

Advanced Endpoint Assessment      : Disabled       perpetual

UC Phone Proxy Sessions           : 2              perpetual

Total UC Proxy Sessions           : 2              perpetual

Botnet Traffic Filter             : Disabled       perpetual

Intercompany Media Engine         : Disabled       perpetual

This platform has a Base license.

Serial Number: JMX1AXXXXX

Running Permanent Activation Key: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Configuration register is 0x1

Configuration has not been modified since last system restart.

fy-a#

Ramraj please do correct me if am wrong.

Please do rate if the given information helps.

By

Karthik

New Member

Unable to see interface on ASA 5510 Firewall

its 7.0 Version .

VIP Purple

Unable to see interface on ASA 5510 Firewall

Then it is normal behaviour. Update to at least 7.22 and you can use all physical interfaces.


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni

Unable to see interface on ASA 5510 Firewall

Hi Pankaj,

Please upgrade your ASA to the higher version. It should be 7.2 4(30) or higher to rectfiy this issue.

Try upgrading the IOS and see whether that comes in picture.

Please do rate if the given information helps.

By

Karthik

838
Views
0
Helpful
8
Replies
CreatePlease login to create content