Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Step-by-Step Configuration and Troubleshooting Best Practices for the NGFW, NGIPS and AMP Technologies A Visual Guide to the Cisco Firepower Threat Defense (FTD)
New Member

when upgrading failover pairLast week I had to upgrade ASA5510

Hardware:   ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW016 @ 0xfff00000, 2048KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode        : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode     : CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode       : CNlite-MC-IPSECm-MAIN-2.06
                             Number of accelerators: 1

0: Ext: Ethernet0/0         : address is f0f7.55f3.25be, irq 9
1: Ext: Ethernet0/1         : address is f0f7.55f3.25bf, irq 9
2: Ext: Ethernet0/2         : address is f0f7.55f3.25c0, irq 9
3: Ext: Ethernet0/3         : address is f0f7.55f3.25c1, irq 9
4: Ext: Management0/0       : address is f0f7.55f3.25bd, irq 11
5: Int: Not used            : irq 11
6: Int: Not used            : irq 5

Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 50             perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Disabled       perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 0              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
             
This platform has a Base license.

Serial Number: JMX1619X0C7
Running Permanent Activation Key: 0xe309e24d 0x50896012 0x98b3ad80 0x98445458 0x0615368e
Configuration register is 0x1
Configuration has not been modified since last system restart.
ciscoasa# ac
ciscoasa# activati
ciscoasa# activation-key e309e24d 50896012 98b3ad80 98445458 0615368e
Validating activation key. This may take a few minutes...
The requested key is the SAME as the flash permanent activation-key.
The flash activation key will not be modified.
ciscoasa#

I would like to the ASA5510 Base license upgrade to Security Plus license. But after the upgrade is still the license of the Base

I think I was wrong option selected in the process of upgrading, how should I do to be successful upgrade

Everyone's tags (6)
2 REPLIES
VIP Purple

when upgrading failover pairLast week I had to upgrade ASA5510

The key you pasted in is not the one that upgrades to SecurityPlus.

How did you get the license? Normally you get a PAK with a number that you enter on http://tools.cisco.com/SWIFT/LicensingUI/Home. After some minutes you get your activation-key by mail.

If that was the key you got, then write a mail to licensing@cisco.com and they can send you the right key.

-- 
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

when upgrading failover pairLast week I had to upgrade ASA5510

Hi Desh,

The key which you have used for activation is the same key that is exist in the ASA. So ASA will not have any changes when you give the same key which is already installed. You should have the different key which should be an licensed key for sec plus bundle.

Serial Number: JMX1619X0C7

Running Permanent Activation Key: 0xe309e24d 0x50896012 0x98b3ad80 0x98445458 0x0615368e

Configuration register is 0x1

Configuration has not been modified since last system restart.

ciscoasa# ac

ciscoasa# activati

ciscoasa# activation-key e309e24d 50896012 98b3ad80 98445458 0615368e

Validating activation key. This may take a few minutes...

The requested key is the SAME as the flash permanent activation-key.

The flash activation key will not be modified.

ciscoasa#

Please do rate if the given information helps.

By

Karthik

554
Views
0
Helpful
2
Replies
CreatePlease to create content