Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

2FE2W -V2 Module Problem

Hi

i recently we brought 3 2FE2W-V2 network modules. i have a tipical problem if i gave one ip address to once interface it will work if i give the same pool of IP address it will not work it is showing interface up Protocol UP but i packet loss . if i gave other pool of ip address it is working . or if i change the slot (i am using 3660 router 64DRAM/32Flash IOS c3640-i-mz.123-14.T6) then it is working but i don't have any problem with old cards. what could be the problem .

Please find the Output and config statements

cd-ajg#sh ip int brief

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 unassigned YES unset administratively down down

FastEthernet0/1 unassigned YES unset administratively down down

cd-ajg#conf t

Enter configuration commands, one per line. End with CNTL/Z.

cd-ajg(config)#int f0/0

cd-ajg(config-if)#ip add 192.168.1.190 255.255.255.0

cd-ajg(config-if)#no shut

cd-ajg(config-if)#^Z

cd-ajg#

*Mar 1 00:04:46.563: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

*Mar 1 00:04:47.107: %SYS-5-CONFIG_I: Configured from console by console

cd-ajg#

cd-ajg#

*Mar 1 00:04:56.623: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

cd-ajg#

cd-ajg#ping 192.168.1.41

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.1.41, timeout is 2 seconds:

.!!!!

Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/4 ms

cd-ajg#conf t

Enter configuration commands, one per line. End with CNTL/Z.

cd-ajg(config)#int f0/1

cd-ajg(config-if)#no ip add

cd-ajg(config-if)#int f0/0

cd-ajg(config-if)#no ip add

cd-ajg(config-if)#^Z

cd-ajg#

*Mar 1 00:05:56.723: %SYS-5-CONFIG_I: Configured from console by console

cd-ajg#conf t

Enter configuration commands, one per line. End with CNTL/Z.

cd-ajg(config)#int f0/1

cd-ajg(config-if)#ip add 192.168.1.190 255.255.255.0

cd-ajg(config-if)#no shut

cd-ajg(config-if)#^Z

cd-ajg#

cd-ajg#

*Mar 1 00:06:29.967: %SYS-5-CONFIG_I: Configured from console by consoleping

*Mar 1 00:06:30.563: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

cd-ajg#

cd-ajg#ping 192.168.1.41

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.1.41, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

cd-ajg#

2 REPLIES

Re: 2FE2W -V2 Module Problem

Hello,

assuming that 192.168.1.41 is a host, how is this host connected to the router (e.g. through a switch, trunk) ? Can you ping the host when you connect the host directly to the FE port(s) ?

Regards,

GNT

New Member

Re: 2FE2W -V2 Module Problem

hi

i am using cross over cable to connect router to my laptop (192.168.1.41), and i worked with switch too.. i am not working on any trunks.

243
Views
0
Helpful
2
Replies