I took the config verbatum and seemed to lose complete access to the AP. So I restored from factory and tried to get to the same place with the settings. I got confused with the interface blocks. There are 3, it seems yours are almost identical. Is that where I am wrong. I can use this as an AP but then it sits where my root AP is. I am not sure what I gain from that. Unless I run an ethernet and make it an AP elswhere. Am I missing something?
Thanks Dan
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$8OuO$tKs4fSgbfusCSIszC5lWz0
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid dpm1028
authentication open
authentication key-management wpa
mbssid guest-mode
infrastructure-ssid optional
wpa-psk ascii 7 020212560F0C0271141C5C
!
!
!
username Cisco password 7 02250D480809
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers tkip
!
broadcast-key change 3600
!
!
ssid dpm1028
!
antenna gain 28
parent 1 001d.7318.fe6e
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role repeater
mobile station scan 2437
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 10.10.92.81 255.255.255.0
no ip route-cache
!
ip default-gateway 10.10.92.1
ip http server
no ip http secure-server
ip http help-path
http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$8OuO$tKs4fSgbfusCSIszC5lWz0
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid dpm1028
authentication open
authentication key-management wpa
mbssid guest-mode
infrastructure-ssid optional
wpa-psk ascii 7 020212560F0C0271141C5C
!
!
!
username Cisco password 7 02250D480809
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers tkip
!
broadcast-key change 3600
!
!
ssid dpm1028
!
antenna gain 28
parent 1 001d.7318.fe6e
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role repeater
mobile station scan 2437
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 10.10.92.81 255.255.255.0
no ip route-cache
!
ip default-gateway 10.10.92.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end
