Re: 2602e Reset to Defaults Except IP not Work over Web GUI

KUMAident · ‎01-23-2014

Hello,

1. Set a Static IP

2. Apply & Save Configuration

3. After Reboot the IP is correct.

Then do Reset to Defaults Except IP in the WEB Gui.

After Reboot the AP loos the static IP and get a DHCP Address.

Reset to Defaults Except IP = Reset to Defaults !

Whats Wrong ?

Scott Fella · ‎01-23-2014

Try it again and console into the ap and reboot it. I would like to see the output.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

KUMAident · ‎01-23-2014

OK, here is:

Writing out the event log to flash:/event.log ...

*Jan 22 17:44:56.675: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram

*Jan 22 17:44:57.547: %SYS-5-RELOAD: Reload requested by on console. Reload Reason: Reload Command.

Write of event.log done

IOS Bootloader - Starting system.

flash is writable

FLASH CHIP: Numonyx Mirrorbit (0089)

Xmodem file system is available.

flashfs[0]: 212 files, 7 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 15058432

flashfs[0]: Bytes available: 16939520

flashfs[0]: flashfs fsck took 23 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: 10:f3:11:c2:2e:3a

Ethernet speed is 1000 Mb - FULL Duplex

Loading "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a"...##########################

File "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a" uncompressed and installed, entry point: 0x2003000

executing...

Secondary Bootloader - Starting system.

Tide MB - 32MB of flash

Xmodem file system is available.

flashfs[0]: 212 files, 7 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 15058432

flashfs[0]: Bytes available: 16939520

flashfs[0]: flashfs fsck took 14 seconds.

Base Ethernet MAC address: 10:f3:11:c2:2e:3a

Boot CMD: 'boot flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a;flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a'

Loading "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a"...#######################################

File "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a" uncompressed and installed, entry point: 0x1003000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 23-Dec-13 08:11 by prod_rel_team

Tide MB - 32MB of flash

Initializing flashfs...

flashfs[3]: 212 files, 7 directories

flashfs[3]: 0 orphaned files, 0 orphaned directories

flashfs[3]: Total bytes: 31739904

flashfs[3]: Bytes used: 15058432

flashfs[3]: Bytes available: 16681472

flashfs[3]: flashfs fsck took 12 seconds.

flashfs[3]: Initialization complete.

flashfs[4]: 0 files, 1 directories

flashfs[4]: 0 orphaned files, 0 orphaned directories

flashfs[4]: Total bytes: 11999232

flashfs[4]: Bytes used: 1024

flashfs[4]: Bytes available: 11998208

flashfs[4]: flashfs fsck took 0 seconds.

flashfs[4]: Initialization complete.

Copying radio files from flash: to ram:

Copy in progress...CCCCC

Copy in progress...CCC

Copy in progress...CCCC

Copy in progress...CC

Copy in progress...CCC

Copy in progress...CC

Copy in progress...CCCCC

Uncompressing radio files...

...done Initializing flashfs.

Radio0 present 8764 8000 0 A8000000 A8010000 0

Rate table has 650 entries (20 legacy/224 11n/406 11ac)

POWER TABLE FILENAME = ram:/B2.bin

Radio1 present 8764 8000 0 88000000 88010000 4

POWER TABLE FILENAME = ram:/B5.bin

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-SAP2602E-E-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.

Processor board ID FGL1711Z6K6

PowerPC CPU at 800Mhz, revision number 0x2151

Last reset from power-on

1 Gigabit Ethernet interface

2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 10:F3:11:C2:2E:3A

Part Number : 73-14511-02

PCA Assembly Number : 800-37898-01

PCA Revision Number : A0

PCB Serial Number : FOC17093TXF

Top Assembly Part Number : 800-38357-01

Top Assembly Serial Number : FGL1711Z6K6

Top Revision Number : A0

Product/Model Number : AIR-SAP2602E-E-K9

Press RETURN to get started!

*Mar 1 00:00:16.035: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory

*Mar 1 00:00:16.151: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (11)APAVC: WlanPAKs 18174 RadioPaks 17566

*Mar 1 00:00:23.131: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)

*Mar 1 00:00:29.443: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)

*Mar 1 00:00:29.503: initializing dot11 onplus

*Mar 1 00:00:29.667: not a autoconfig enabled device!!!

*Mar 1 00:00:31.671: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar 1 00:00:32.671: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down

*Mar 1 00:01:18.015: Starting Ethernet promiscuous mode

*Jan 22 17:44:57.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down

*Jan 22 17:44:57.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down

*Jan 22 17:44:57.007: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source

*Jan 22 17:44:57.015: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 23-Dec-13 08:11 by prod_rel_team

*Jan 22 17:44:57.015: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start

*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to downERROR: Failed to configure ethernet promiscuous mode. Interface Descriptor mismatch

*Jan 22 17:45:01.667: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (0-0)

*Jan 22 17:45:01.667: DPAA Initialization Complete

*Jan 22 17:45:01.667: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited

*Jan 22 17:45:02.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

*Jan 22 17:45:06.863: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.16.33.216, mask 255.255.254.0, hostname ap

Scott Fella · ‎01-23-2014

Can you add a static and then just reboot the AP. Just want to compare the output. Don't reset to default.

Also can you post the show ip int brief before and after.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

KUMAident · ‎01-23-2014

Here is the show ip dump:

show ip interface

BVI1 is up, line protocol is up

Internet address is 10.16.33.100/23

Broadcast address is 255.255.255.255

Address determined by configuration file

MTU is 1500 bytes

Helper address is not set

Directed broadcast forwarding is disabled

Multicast reserved groups joined:

Outgoing access list is not set

Inbound access list is not set

Proxy ARP is enabled

Local Proxy ARP is disabled

Security level is default

Split horizon is enabled

ICMP redirects are always sent

ICMP unreachables are always sent

ICMP mask replies are never sent

IP fast switching is disabled

IP fast switching on the same interface is disabled

IP CEF switching is disabled

IP Null turbo vector

IP multicast fast switching is disabled

--More-- IP multicast distributed fast switching is disabled

IP route-cache flags are Fast

Router Discovery is disabled

IP output packet accounting is disabled

IP access violation accounting is disabled

TCP/IP header compression is disabled

RTP/IP header compression is disabled

Policy routing is disabled

Network address translation is disabled

BGP Policy Mapping is disabled

Input features: MCI Check

Dot11Radio0 is administratively down, line protocol is down

Internet protocol processing disabled

Dot11Radio1 is administratively down, line protocol is down

Internet protocol processing disabled

GigabitEthernet0 is up, line protocol is up

Internet protocol processing disabled

ap#

################################################

Cant find the add static command.

Rasika Nayanajith · ‎01-23-2014

Hi

I think Scott mean configure a static IP on your BVI1 interface & save the config & reload. Something like this.

ap#conf t

ap(config)#int bvi1

ap(config-if)#ip add 10.16.33.33 255.255.254.0

ap(config-if)#end

!

write mem

!

reload

See wether IP address get dissapear after reload

HTH

Rasika

*** Pls rate all useful responses ****

KUMAident · ‎01-24-2014

Thank you Rasika,

Here is the BVI1 after Reload.

BVI1 is up, line protocol is up 1 00:00:29.675: not a autoconf

Hardware is BVI, address is 10f3.11c2.2e3a (bia 10f3.11c2.2e3a)

*Mar 1 00:00:31.675: %LINK-6-UPDOWN: Interface Gigabi

Internet address is 10.16.33.100/23

MTU 1500 bytes, BW 54000 Kbit/sec, DLY 50

++++++++++++++++++++++++++++++++++++++++++++++++

If I set the BVI1 Interface over cli or gui the ip parameter are saved correkt and the ap

after boot or reload have the correkt ip.

The problem is the "Reset to Defaults (Except IP)" Button on Gui.

If i click the button the ap set all parameters to defaults and the BVI1 to DHCP.

But "Except IP" shold be not change the ip !

Rasika Nayanajith · ‎01-24-2014

Ok, If you have tested it & everytime behaviour is same (you loose the IP config once you do this via GUI) it may be GUI related bug.

You can try this with different IOS image (upgading or downgrading) & see whether behavioiur is same ? if not it may be specific to the code you are running.

HTH

Rasika

**** Pls rate all useful responses ****

KUMAident · ‎01-24-2014

The Version is: ap3g2-k9w7-xx.152-4.JB3a

It´s definitly a gui related bug.

Insted a "reset to defaults except ip" i load a default config with correct ip settings.

Hope this bug will be solved in the future.

Sandeep Choudhary · ‎01-24-2014

Hi,

These are the only Open Caveats in 15.2(4) JB3a:

Open Caveats

CSCud51131 CLI required to configure IPv6 SNTP server addresses.

CSCue53185 The allowed frequencies are repeated in show controllers dot111 command for Japan regdomain.

CSCuf85579 Multicast downstream fails on a wlan client with security wpa2-tkip on enabling broadcast key rotation.

CSCui79550 GUI IP Protocol 119 column missing on the QoS policies page.

CSCuj62328 Apple client is not associating with 11r SSID.

CSCul91975 WGB may disconnect permanently after max retry of 802.11 probe.

If you can reproduce this BUG then U can raise a TAC case, it may help to other.

Regards

Scott Fella · ‎01-24-2014

Downgrade the version to v12.4... v15 is no good... Too many complaints with the newer version. The latest v12.4 is what you should use.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

Scott Fella · ‎01-24-2014

Well they use to have a v12.4 for the ap3g2 AP's you can use... They removed it. So now you just have to try one of the other v15 code versions. The newer code is awful and I have no idea why they went that route.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

Scott Fella · ‎01-24-2014

Ah now I remember... The radios for the 1262's and the 3600's were the same, so you were able to load the 1262 code into the 3600. I'm guessing since the 3600 is the higher version of the 2nd gen you might be able to use it on the 2600 also. If I have time today I'll test that.

Is defaulting the AP except for an IP something you really want to work? I mean you can write erase on the CLI and put the static back on and personally, autonomous AP's should be configured from the CLI. Just wondering if you want to go through the hassle if upgrading or downgrading because of that one issue. I would be worried a both other issues that might affect production.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***