Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

871 Not advertising SSID

When trying to view available wireless networks - I am not able to see "intheair" advertised. Am I missing anything? Thanks.

dot11 ssid intheair

vlan 1

authentication open

authentication key-management wpa

infrastructure-ssid optional

wpa-psk ascii 7 jabadahutcantina

interface Dot11Radio0

no ip address

!

encryption vlan 1 mode ciphers tkip

!

ssid intheair

!

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0

station-role root

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: 871 Not advertising SSID

Hi Michael,

The command that controls the "Broadcast" of the SSID is "guest mode". Have a look;

guest-mode (SSID configuration mode)

Use the guest-mode SSID configuration mode command to configure the radio interface (for the specified SSID) to support guest mode. Use the no form of the command to disable the guest mode.

[no] guest-mode

The access point can have one guest-mode SSID or none at all. The guest-mode SSID is used in beacon frames and response frames to probe requests that specify the empty or wildcard SSID. If no guest-mode SSID exists, the beacon contains no SSID and probe requests with the wildcard SSID are ignored. Disabling the guest mode makes the networks slightly more secure. Enabling the guest mode helps clients that passively scan (do not transmit) associate with the access point. It also allows clients configured without a SSID to associate.

Examples

This example shows how to set the wireless LAN for the specified SSID into guest mode:

(config-if-ssid)# guest-mode

This example shows how to reset the guest-mode parameter to default values (no broadcast SSID):

(config-if-ssid)# no guest-mode

From this IOS Command doc;

http://www.cisco.com/en/US/products/hw/routers/ps272/products_technical_reference_chapter09186a008022e0e3.html#wp2641711

Hope this helps!

Rob

1 REPLY
Hall of Fame Super Red

Re: 871 Not advertising SSID

Hi Michael,

The command that controls the "Broadcast" of the SSID is "guest mode". Have a look;

guest-mode (SSID configuration mode)

Use the guest-mode SSID configuration mode command to configure the radio interface (for the specified SSID) to support guest mode. Use the no form of the command to disable the guest mode.

[no] guest-mode

The access point can have one guest-mode SSID or none at all. The guest-mode SSID is used in beacon frames and response frames to probe requests that specify the empty or wildcard SSID. If no guest-mode SSID exists, the beacon contains no SSID and probe requests with the wildcard SSID are ignored. Disabling the guest mode makes the networks slightly more secure. Enabling the guest mode helps clients that passively scan (do not transmit) associate with the access point. It also allows clients configured without a SSID to associate.

Examples

This example shows how to set the wireless LAN for the specified SSID into guest mode:

(config-if-ssid)# guest-mode

This example shows how to reset the guest-mode parameter to default values (no broadcast SSID):

(config-if-ssid)# no guest-mode

From this IOS Command doc;

http://www.cisco.com/en/US/products/hw/routers/ps272/products_technical_reference_chapter09186a008022e0e3.html#wp2641711

Hope this helps!

Rob

357
Views
0
Helpful
1
Replies
CreatePlease to create content