Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

871w wireless configuration

Hello,

I know this question was asked many times, but I'm still not able to finalize my configuration on 871w. LAN part works fine, but wireless clients do not get DHCP IP. here is the config:

Building configuration...

Current configuration : 2092 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname WROUTER

!

boot-start-marker

boot-end-marker

!

logging message-counter syslog

logging buffered 4096

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid sputnik

vlan 1

authentication open

!

ip source-route

!

!

no ip dhcp use vrf connected

ip dhcp excluded-address 192.168.1.254

!

ip dhcp pool vlan1

network 192.168.1.0 255.255.255.0

default-router 192.168.1.254

dns-server 167.206.245.7 167.206.245.71

lease 10

!

!

ip cef

no ip domain lookup

no ipv6 cef

!

multilink bundle-name authenticated

!

!

!

!

!

!

archive

log config

hidekeys

!

!

!

bridge irb

!

!

interface FastEthernet0

!

interface FastEthernet1

!

interface FastEthernet2

!

interface FastEthernet3

!

interface FastEthernet4

ip address dhcp

ip nat outside

ip virtual-reassembly

duplex auto

speed auto

no cdp enable

!

interface Dot11Radio0

no ip address

!

encryption vlan 1 mode wep mandatory

!

encryption key 1 size 128bit 0 0D9E3A3AF78EA7A156A6D6FB09 transmit-key

!

ssid sputnik

!

speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0

station-role root

no cdp enable

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

no ip address

ip virtual-reassembly

bridge-group 1

bridge-group 1 spanning-disabled

!

interface BVI1

ip address 192.168.1.254 255.255.255.0

ip nat inside

ip virtual-reassembly

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 dhcp

ip http server

no ip http secure-server

!

!

ip nat inside source list 1 interface FastEthernet4 overload

!

access-list 1 permit 192.168.1.0 0.0.0.255

!

!

!

!

!

control-plane

!

bridge 1 protocol ieee

bridge 1 route ip

!

line con 0

no modem enable

line aux 0

line vty 0 4

login

!

scheduler max-task-time 5000

end

I'dliket o have LAN and WLAN clients in same 192.168.1.0 subnet.

Thanks.

3 REPLIES

Re: 871w wireless configuration

try removing the VLAN statement under the SSID, and the encryption lines. Just place the main Dot11Radio0 Interface in Bridge-group 1 and see how that works for you. SO:

dot11 ssid sputnik

authentication open

no interface dot0.1

int dot0

bridge-group 1

HTH,

Steve

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Re: 871w wireless configuration

thank you.

I read this forum and i found that I need vlan 1 for each encryption line. Here is the config that works for me:

Building configuration...

Current configuration : 2130 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname xxxxx

!

boot-start-marker

boot-end-marker

!

logging message-counter syslog

logging buffered 4096

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid sputnik

vlan 1

authentication open

guest-mode

!

ip source-route

!

!

no ip dhcp use vrf connected

ip dhcp excluded-address 192.168.1.254

!

ip dhcp pool vlan1

network 192.168.1.0 255.255.255.0

default-router 192.168.1.254

dns-server 167.206.245.7 167.206.245.71

lease 10

!

!

ip cef

no ip domain lookup

no ipv6 cef

!

multilink bundle-name authenticated

!

!

!

!

!

!

archive

log config

hidekeys

!

!

!

bridge irb

!

!

interface FastEthernet0

!

interface FastEthernet1

!

interface FastEthernet2

!

interface FastEthernet3

!

interface FastEthernet4

ip address dhcp

ip nat outside

ip virtual-reassembly

duplex auto

speed auto

no cdp enable

!

interface Dot11Radio0

no ip address

!

encryption vlan 1 key 1 size 128bit 0 0D9E3A3AF78EA7A156A6D6FB09 transmit-key

encryption vlan 1 mode wep mandatory

!

ssid sputnik

!

speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0

station-role root

no cdp enable

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

no ip address

ip nat inside

ip virtual-reassembly

bridge-group 1

bridge-group 1 spanning-disabled

!

interface BVI1

ip address 192.168.1.254 255.255.255.0

ip nat inside

ip virtual-reassembly

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 dhcp

ip http server

no ip http secure-server

!

!

ip nat inside source list 1 interface FastEthernet4 overload

!

access-list 1 permit 192.168.1.0 0.0.0.255

!

!

!

!

!

control-plane

!

bridge 1 protocol ieee

bridge 1 route ip

!

line con 0

password cisco

login

no modem enable

line aux 0

line vty 0 4

password cisco

login

!

scheduler max-task-time 5000

end

New Member

871w wireless configuration

This is what I got and it has been working for me. From my modem to my RV016 to my 871w.  Once I figure out the PPPOE the 871w will be my only router running, and figure out the port forwarding, but most important I need to configure PPPOE.

mr-r1#sh star

Using 3825 out of 131072 bytes

!

! Last configuration change at 08:10:30 PCTime Sun Oct 28 2012 by ramosm

! NVRAM config last updated at 08:10:33 PCTime Sun Oct 28 2012 by ramosm

!

version 12.4

no service pad

service timestamps debug datetime msec localtime

service timestamps log datetime msec localtime

no service password-encryption

!

hostname mr-r1

!

boot-start-marker

boot-end-marker

!

logging message-counter syslog

logging buffered 64000

logging rate-limit 20

enable secret 5 $1$PDK9$YSz8GsnVsDYevR1hVGMG70

!

aaa new-model

!

!

aaa authentication login default local

aaa authorization exec default local

!

!

aaa session-id common

clock timezone PCTime -8

clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00

!

crypto pki trustpoint TP-self-signed-3978252741

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-3978252741

revocation-check none

rsakeypair TP-self-signed-3978252741

!

!

crypto pki certificate chain TP-self-signed-3978252741

certificate self-signed 01 nvram:IOS-Self-Sig#B.cer

dot11 syslog

!

dot11 ssid ramfam

vlan 55

authentication open

mbssid guest-mode

!

ip source-route

no ip dhcp use vrf connected

ip dhcp excluded-address 10.25.55.1 10.25.55.49

ip dhcp excluded-address 10.25.55.76 10.25.55.254

ip dhcp excluded-address 10.25.50.1 10.25.50.49

ip dhcp excluded-address 10.25.50.76 10.25.50.254

!

ip dhcp pool Data

   import all

   network 10.25.50.0 255.255.255.0

   dns-server 10.55.55.1 4.2.2.1

   domain-name MR-Lab1

   default-router 10.25.50.1

   lease 25

!

ip dhcp pool Wireless

   import all

   network 10.25.55.0 255.255.255.0

   default-router 10.25.55.1

   dns-server 10.55.55.1 4.2.2.2

   lease 25

!

!

ip cef

ip domain name MR-Lab1.com

ip name-server 10.55.55.1

!

!

!

!

username ramosm privilege 15 secret 5 $1$J2cq$abQJlRlZgmIlEDPX/jd8A1

!

!

!

archive

log config

  hidekeys

!

!

no ip ftp passive

!

bridge irb

!

!

interface FastEthernet0

description AirNet 1100

speed 100

spanning-tree portfast

!

interface FastEthernet1

description Extra cat5

spanning-tree portfast

!

interface FastEthernet2

description Ubuntu PC

spanning-tree portfast

!

interface FastEthernet3

description PS3

speed 100

spanning-tree portfast

!

interface FastEthernet4

description Internet Wan Port

ip address 10.55.55.105 255.255.255.0

ip nat outside

ip virtual-reassembly

speed 100

full-duplex

!

interface Dot11Radio0

no ip address

!

encryption vlan 55 key 1 size 128bit 0 AB2081CA12B126DD2F95ABCF32 transmit-key

encryption vlan 55 mode wep mandatory

!

broadcast-key vlan 55 change 30

!

!

ssid ramfam

!

mbssid

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0

station-role root

!

interface Dot11Radio0.55

encapsulation dot1Q 55 native

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

ip address 10.25.50.1 255.255.255.0

ip nat inside

ip virtual-reassembly

!

interface Vlan55

no ip address

bridge-group 1

!

interface BVI1

ip address 10.25.55.1 255.255.255.0

ip nat inside

ip virtual-reassembly

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 10.55.55.1

ip http server

ip http authentication local

ip http secure-server

!

ip nat inside source list 1 interface FastEthernet4 overload

ip nat inside source list 2 interface FastEthernet4 overload

!

access-list 1 remark SDM_ACL Category=2

access-list 1 permit 10.25.50.0 0.0.0.255

access-list 2 remark SDM_ACL Category=2

access-list 2 permit 10.25.55.0 0.0.0.255

!

!

!

!

control-plane

!

bridge 1 protocol ieee

bridge 1 route ip

!

line con 0

exec-timeout 30 0

password Cisco

logging synchronous

no modem enable

line aux 0

line vty 0 4

exec-timeout 20 0

password Cisco

logging synchronous

!

scheduler max-task-time 5000

end

mr-r1#

1825
Views
0
Helpful
3
Replies