cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3751
Views
0
Helpful
27
Replies

AIR-CAP3602I-N-K9 not detected by WLC 2500

kaustav.gupta
Level 1
Level 1

                   Hi All,

I have connected a AIR-CAP3602I-N-K9 Ethernet port to the POE port 4 of the WLC. I configured the basic settings in the WLC and it is accessible via Web GUI. The AP page shows no AP detected. The lights on the AP is blinking GREEN. I am not sure what to do next. Kindly help.

27 Replies 27

kaustav.gupta
Level 1
Level 1

AP Boot

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.01.19 20:49:02 =~=~=~=~=~=~=~=~=~=~=~=

IOS Bootloader - Starting system.
flash is writable
FLASH CHIP:  Macronix Mirrorbit (00C2)
Xmodem file system is available.
flashfs[0]: 5 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 5190656
flashfs[0]: Bytes available: 26807296
flashfs[0]: flashfs fsck took 13 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: e4:c7:22:f0:4d:4f
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...####################################################################################################################################################################################################################################################

File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 12.4(25e)JAL1a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 06-Mar-13 21:54 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP:  Macronix Mirrorbit (00C2)

flashfs[1]: 5 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31739904
flashfs[1]: Bytes used: 5190656
flashfs[1]: Bytes available: 26549248
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 0 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP3602I-N-K9    (PowerPC) processor (revision A0) with 167926K/81920K bytes of memory.
Processor board ID FGL1743S656
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.3.1.53
1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E4:C7:22:F0:4D:4F
Part Number                          : 73-14521-02
PCA Assembly Number                  : 800-37501-02
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17390MHE
Top Assembly Part Number             : 800-35852-02
Top Assembly Serial Number           : FGL1743S656
Top Revision Number                  : C0
Product/Model Number                 : AIR-CAP3602I-N-K9  
% Please define a domain-name first.
logging facility kern
        ^
% Invalid input detected at '^' marker.

logging trap emergencies
        ^
% Invalid input detected at '^' marker.

logging facility kern
        ^
% Invalid input detected at '^' marker.

logging trap emergencies
        ^
% Invalid input detected at '^' marker.

Press RETURN to get started!


*Mar  1 00:00:09.355: %LWAPP-4-CLIENTEVENTLOG: Unable to open event log file flash:/event.log

*Mar  1 00:00:09.355: %LWAPP-4-CLIENTEVENTLOG: Read and initialized AP event log (contains, 0 messages)

*Mar  1 00:00:11.207: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:11.279: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 12.4(25e)JAL1a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 06-Mar-13 21:54 by prod_rel_teamlwapp_crypto_init: MIC Present and Parsed Successfully

*Sep 25 05:45:13.927: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Sep 25 05:45:14.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Sep 25 05:45:15.791: DPAA Initialization Complete
*Sep 25 05:45:15.791: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Sep 25 05:45:16.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Sep 25 05:45:16.391: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED AIR-CT2504-K9 (c08c.60c6.e1a7)
*Sep 25 05:45:17.391: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED AIR-CT2504-K9 (c08c.60c6.e1a7)
*Sep 25 05:45:52.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:46:02.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:46:12.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:46:22.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:46:32.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Sep 25 05:46:42.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:46:42.039: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Sep 25 05:46:52.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:47:02.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:47:12.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:47:22.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Sep 25 05:47:32.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:47:32.039: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Sep 25 05:47:42.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:47:52.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:48:02.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:48:12.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Sep 25 05:48:22.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:48:22.039: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Sep 25 05:48:32.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:48:42.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:48:52.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:49:02.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Sep 25 05:49:12.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 25 05:49:12.039: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Sep 25 05:49:22.039: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!

as you can see that AP not getting IP .

Either configure static IP or connect to AP to a swicth and create a DHCP pool on Switch.

Static IP on AP:

AP#lwapp ap ip address  
AP#lwapp ap ip default-gateway
AP#lwapp ap controller ip address
AP#lwapp ap hostname

https://supportforums.cisco.com/docs/DOC-18274

Regards

HI sandeep ,

I was really looking for this commands as it is an LWAPP image.

I configured and IP address in the AP and the output changed to

*Jan 19 21:09:54.739: %CAPWAP-3-ERRORLOG: Go join a capwap controller

examining image...!

extracting info (286 bytes)

Image info:

    Version Suffix: k9w8-.152-4.JA1

    Image Name: ap3g2-k9w8-mx.152-4.JA1

    Version Directory: ap3g2-k9w8-mx.152-4.JA1

    Ios Image Size: 758272

    Total Image Size: 11520512

    Image Feature: WIRELESS LAN|LWAPP

    Image Family: AP3G2

    Wireless Switch Management Version: 7.5.102.0

Extracting files...

ap3g2-k9w8-mx.152-4.JA1/ (directory) 0 (bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/img_sign_rel_sha2.cert (1371 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/B5.bin (1816 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/V5.bin (525 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/img_sign_rel.cert (1375 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/Y5.bin (1524 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/file_hashes (5001 bytes)!

extracting ap3g2-k9w8-mx.152-4.JA1/B2.bin (9328 bytes)

*Jan 19 21:09:55.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.1.100 peer_port: 5246

*Jan 19 21:09:55.463: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.1.100 peer_port: 5246

*Jan 19 21:09:55.467: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.1.100

*Jan 19 21:09:5!

extracting ap3g2-k9w8-mx.152-4.JA1/X5.bin (1487 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/final_hash.sig (513 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/final_hash (141 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/info (286 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/E5.bin (1803 bytes)

extracting ap3g2-k9w8-mx.152-4.JA1/Y2.bin (5830 bytes)!

extracting ap3g2-k9w8-mx.152-4.JA1/V2.bin (12826 bytes)!

extracting ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1 (206045 bytes)5.467: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.

*Jan 19 21:09:55.467: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.

*Jan 19 21:09:55.467: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller

*Jan 19 21:09:55.467: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.1.100FirstCapwapVersionHasIma!!!!!!ge = 7.1.1.0

perform archive download capwap:/ap3g2 tar file

*Jan 19 21:09:55.467: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.

*Jan 19 21:09:55.471: Loading file /ap3g2...

!!!!!!!!!

extracting ap3g2-k9w8-mx.152-4.JA1/8004.img (541961 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

extracting ap3g2-k9w8-mx.152-4.JA1/E2.bin (18656 bytes)!!

extracting ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1 (10519307 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Just remember, the issue you will have is the clients might not get ip address and many features like mDNS, multicast, etc are not supported when an AP is directly connected.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***

Hi Kaustav,

Can you connect AP to switch.

Creat a dhcp pool in whcih u wat AP to get IP.

Example:

ip dhcp excluded-address 10.99.80.1 10.99.80.100

ip dhcp excluded-address 10.99.80.110 10.99.80.254

!

ip dhcp pool WirelessLAN

   network 10.99.80.0 255.255.255.0

   default-router 10.99.80.254

   option 43 ip 10.99.80.1 ---> wlc IP

   lease 3

!

interface FastEthernet0/22

description *** AP ***

switchport access vlan x

Regards

Dont forget to rate helpful posts

Can you please post the output to the command "sh ap summary"?  I want to see the first page only.

Leo... The OP wants to connect the AP directly to the 2504 PoE port.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

Leo... The OP wants to connect the AP directly to the 2504 PoE port.

No problem with that.  I'm concerned about the amount of APs the WLC is already supporting. 

True:)

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

True:)

Darn it, Scott!  You blew my cover. 

Haha

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

2 Nos AP's AIR-CAP 3602I-N-K9

I want to see the output please to the command "sh ap summary".

Sent from Cisco Technical Support Wii App

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: