Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Aironet 1040 WAP disconnects / will not allow connect

     I have two Aironet 1040 WAPs, AP1 and AP2, and am getting diconnects as well as it will not let you connect about once a day on AP1. The log reads "Interface Dot11Radio0, Deathenticating station (MAC Address here) Reason:Sending station has left the BSS"

I have firmware updated to current release on both, 12.4(25d)JA

If i reboot after this starts happening connections will be allowed.

Anybody have any ideas what might be causing this particular WAP to be a pain?

1 ACCEPTED SOLUTION

Accepted Solutions

Aironet 1040 WAP disconnects / will not allow connect

Ok, let's try this.

Under TB_Wireless

no mbssid guest-mode

no guest-mode

no infrastucture-ssid optional (not needed for clients, just for bridging)

Under TaylorBros-Guest

no mbssid guest-mode

guest-mode

Under Dot11Radio0

no mbssid

no dot11 extensions aironet

What we are doing, is removig the mbssid IE from the beacons.  it also limits only the Guest SSID to being broadcast.  Anyone wanting to use the TB_Wireless would need to configure the profile on their device. 

If it doesn't help, you can put the commands back on, I've just seen the mbssid commands cause some issues depending on the clients.

HTH,

Steve

----------------------------------------------------------------------------------------------------------

Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
7 REPLIES

Aironet 1040 WAP disconnects / will not allow connect

Sam,

     What type of device is having this issue?  Are the drivers for the NIC up to date?  Which supplicant is being used?

HTH,

Steve

----------------------------------------------------------------------------------------------------------

Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Aironet 1040 WAP disconnects / will not allow connect

It does not seem to matter what device Laptop, IPAD , IPhone. PArdon my ignorance, help me with supplicant?

Aironet 1040 WAP disconnects / will not allow connect

supplicant is the software used to configure the wireless profile.  So like IntelProset, Windows Zero Config(native windows client) etc.

Can you pull the config from teh AP and attach them so we can see what it looks like?

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Re: Aironet 1040 WAP disconnects / will not allow connect

Aha, with having just the Two WAPs i do not use any additional software to manage/config them. Maybe i should be?  I have attached the config file

Aironet 1040 WAP disconnects / will not allow connect

Ok, let's try this.

Under TB_Wireless

no mbssid guest-mode

no guest-mode

no infrastucture-ssid optional (not needed for clients, just for bridging)

Under TaylorBros-Guest

no mbssid guest-mode

guest-mode

Under Dot11Radio0

no mbssid

no dot11 extensions aironet

What we are doing, is removig the mbssid IE from the beacons.  it also limits only the Guest SSID to being broadcast.  Anyone wanting to use the TB_Wireless would need to configure the profile on their device. 

If it doesn't help, you can put the commands back on, I've just seen the mbssid commands cause some issues depending on the clients.

HTH,

Steve

----------------------------------------------------------------------------------------------------------

Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Re: Aironet 1040 WAP disconnects / will not allow connect

Steve

I uploaded the config file on both WAPs and i cannot connect to them via http. However i can connect to use wireless.

New Member

Re: Aironet 1040 WAP disconnects / will not allow connect

whoops, i uploaded sam config file to both WAPs giving them identical ip addresses. OK, i remedied that and am back up and working. Small panic attack

916
Views
0
Helpful
7
Replies
CreatePlease to create content