Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AP 1140 conifguration for a survey

Hi,

I am all new to this. I have a stand alone 1140 AP and i am trying to perform a site survey using the AP; However I dont know what configs need to be on the AP for the survey ? can you help me please?

Everyone's tags (5)
5 REPLIES

AP 1140 conifguration for a survey

all you need is a very basic config.  Just be sure to set the power to half what the client can support.

dot11 ssid Survey

   authentication open

   authentication key-management wpa version 2

   wpa-psk ascii 0 Survey1234

!!

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm

!

ssid Survey

HTH,
Steve

-----------------------------------------
Please remember to rate useful posts, and mark questions as answered

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

AP 1140 conifguration for a survey

Thank you for your quick answer.

Both Radios need to be on? Radio0 and Radion1 which one is the 2.4 and 5 ghz?

Re: AP 1140 conifguration for a survey

It depends.  If you are only looking for 2.4GHz, then no.  But if you want 5GHz coverage as well, then yes.

Radio0 is the 2.4

Radio1 is the 5

HTH,
Steve

-----------------------------------------
Please remember to rate useful posts, and mark questions as answered

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

AP 1140 conifguration for a survey

This What I have on the AP right now.

the ssid "Survey" needs to be brodcasted for the Survey? if so how can i set ip up on th eAP?

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid Survey

   authentication open

   authentication key-management wpa version 2

!

!

!

username Cisco password 7 05280F1C2243

!

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm

!

ssid Survey

!

antenna gain 0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface Dot11Radio1

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm

!

ssid Survey

!

antenna gain 0

dfs band 3 block

channel dfs

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface GigabitEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

no keepalive

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address dhcp client-id GigabitEthernet0

no ip route-cache

!

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

!

!

!

line con 0

line vty 0 4

login local

!

end

AP 1140 conifguration for a survey

under the SSID add the command guest-mode.  that will broadcast the SSID.  Don't forget to add in your wpa key as well

HTH,
Steve

-----------------------------------------
Please remember to rate useful posts, and mark questions as answered

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
500
Views
0
Helpful
5
Replies
CreatePlease to create content