Hey guys, I'm trying to set up a standalone access point (1252) with a few vlans and a trunk going to a 2960 switch.
I've also got my ssids attached to vlans, a radio sub-interface and gig sub-interface for each vlan, and a trunk going from the gigabit interface on the AP to my 2960
My problem is that I have no connectivity between associated clients on the AP, or between the AP (BVI1 interface) and a hard wired client on the 2960.
Here are the relevent portions of my running-config
dot11 vlan-name Houston vlan 11 dot11 vlan-name IT vlan 7 dot11 vlan-name nuaWireless vlan 70 ! dot11 ssid Houston vlan 11 authentication open authentication key-management wpa version 1 mbssid guest-mode wpa-psk ascii 7 0208115A59081A201E ! dot11 ssid IT vlan 7 authentication open authentication key-management wpa version 1 guest-mode mbssid guest-mode wpa-psk ascii 7 0208115A58081A201F ! dot11 ssid nuaWireless vlan 70 authentication open authentication key-management wpa version 1 mbssid guest-mode wpa-psk ascii 7 0701344D1F070C0446 !
interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers tkip ! encryption vlan 70 mode ciphers tkip ! encryption vlan 11 mode ciphers tkip ! encryption vlan 7 mode ciphers tkip ! ssid Houston ! ssid IT ! ssid nuaWireless ! mbssid station-role root ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.7 encapsulation dot1Q 7 no ip route-cache bridge-group 7 bridge-group 7 subscriber-loop-control bridge-group 7 block-unknown-source no bridge-group 7 source-learning no bridge-group 7 unicast-flooding bridge-group 7 spanning-disabled ! interface Dot11Radio0.11 encapsulation dot1Q 11 no ip route-cache bridge-group 11 bridge-group 11 subscriber-loop-control bridge-group 11 block-unknown-source no bridge-group 11 source-learning no bridge-group 11 unicast-flooding bridge-group 11 spanning-disabled ! interface Dot11Radio0.70 encapsulation dot1Q 70 no ip route-cache bridge-group 70 bridge-group 70 subscriber-loop-control bridge-group 70 block-unknown-source no bridge-group 70 source-learning no bridge-group 70 unicast-flooding bridge-group 70 spanning-disabled !
interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto ! interface GigabitEthernet0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface GigabitEthernet0.7 encapsulation dot1Q 7 no ip route-cache bridge-group 7 no bridge-group 7 source-learning bridge-group 7 spanning-disabled ! interface GigabitEthernet0.11 encapsulation dot1Q 11 no ip route-cache bridge-group 11 no bridge-group 11 source-learning bridge-group 11 spanning-disabled ! interface GigabitEthernet0.70 encapsulation dot1Q 70 no ip route-cache bridge-group 70 no bridge-group 70 source-learning bridge-group 70 spanning-disabled ! interface BVI1 ip address 10.7.1.200 255.255.0.0 no ip route-cache !
Transferring Crash file from standby:
Login to the Active WLC in HA.
(Cisco Controller) >transfer upload datatype crash
(Cisco Controller) >transfer upload filename <Desired filename>
(Cisco Controller) >transfer up...
This is the start of a display filter cross reference between Wireshark and OmniPeek.
The 1st installment is a table of advanced filters. More filters will be added as time allows.
It is a living doc, so check back for changes every so often
Please feel ...
I have created a Powershell script to automatically add a Wireless Guest User on Cisco WLCs. (tested on 2500 Series)
The script should be completely self explanatory.
Powershell SNMP Module (Install-Module -Name SNMP)
SNMP Write Access to...