Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AP 2600 problem

IOS Bootloader - Starting system.

flash is writable

FLASH CHIP:  Numonyx Mirrorbit (0089)

Xmodem file system is available.

flashfs[0]: 39 files, 9 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 18512896

flashfs[0]: Bytes available: 13485056

flashfs[0]: flashfs fsck took 17 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: 7c:ad:74:db:52:37

Ethernet speed is 100 Mb - FULL Duplex

Loading "flash"...flash: permission denied

Error loading "flash"

Interrupt within 5 seconds to abort boot process.

Loading "/ap3g2-k9w8-mx.152-2.JB".../ap3g2-k9w8-mx.152-2.JB: permission denied

Error loading "/ap3g2-k9w8-mx.152-2.JB"

Interrupt within 5 seconds to abort boot process.

Loading "flash:/ap3g2-k9w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB"...uncompress: Unknown mzip segment type: 2

Error loading "flash:/ap3g2-k9w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB"

Interrupt within 5 seconds to abort boot process.

Boot process failed...

The system is unable to boot automatically.  The BOOT

environment variable needs to be set to a bootable

image.

C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 30-May-12 03:34 by binugopa

ap:

ap:

ap:

3 REPLIES
Hall of Fame Super Silver

AP 2600 problem

You need to upload new code:

https://supportforums.cisco.com/thread/2043235

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver
VIP Purple

AP 2600 problem

HI Walid,

Try this method:

Make sure the AP has network-connectivity to an TFTP-server (Example Tftp is at ip, 10.10.10.10). Then issue the following commands;

ap: set IP_ADDR 10.10.10.20

ap: set NETMASK 255.255.255.0

ap: set DEFAULT_ROUTER 10.10.10.1

ap: tftp_init

Then we delete the current IOS (.tar). We are now ready to copy the new IOS (and properly this time). Issue the following command;

ap: delete flash:

Are you sure you want to delete "flash:r" (y/n)?y

File "flash:r" deleted

ap: tar -xtract tftp://10.10.10.10/flash:

Then boot the newly extracted IOS;

ap: boot

Loading "flash:"...flash:: no such file or directory

Error loading "flash:"

Interrupt within 5 seconds to abort boot process.

Loading "flash://"...############

File "flash://" uncompressed and installed, entry point: 0x4000

-------------------------------------------------------------------------------------------------------------------------

Please also check this dcoument:

https://supportforums.cisco.com/docs/DOC-14636

Regards

261
Views
4
Helpful
3
Replies
CreatePlease login to create content