I have a Cisco 521 Acces Point - the standalone version.
It had some problems with the IOS and I made an up-grade.
It is now running the latest version: 12.4
I cannot configure the Acces Point from the web interface - most of the pages are missing or giving me script errors,
so I started to configure the AP fom console interface (via serial cable).
The network design is simple:
192.168.0.1 - a Linksys RV042 router acting as gateway, DHCP server and DNS proxy.
192.168.0.2 - Cisco 521 Acces Point
192.168.0.3 - Cisco Catalyst 2960 switch
Starting from 192.168.0.10 up to .100 I have a DHCP IP address range.
Below you can see the acces point configuration:
Current configuration : 1576 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Aironet ! enable secret 5 $1$bTcL$bxwAydUMKA4z0TXcMgEf6/ enable password 7 033E0B190D0301424A ! no aaa new-model ip name-server 192.168.0.1 ip dhcp smart-relay ip dhcp relay information policy keep ! ! ip dhcp-server 192.168.0.1 ! dot11 ssid ServiceCenter authentication open authentication key-management wpa version 2 guest-mode wpa-psk ascii 7 012003164D02050A0249401D1C17 ! power inline negotiation prestandard source ! ! username Cisco password 7 13261E010803 username admin privilege 15 password 7 0735715E4505390B13 ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers tkip ! ssid ServiceCenter ! station-role root access-point bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface FastEthernet0 no ip address no ip route-cache duplex auto speed auto bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 ip dhcp relay information trusted ip address 192.168.0.2 255.255.255.0 ip helper-address 192.168.0.1 no ip route-cache ! ip default-gateway 192.168.0.1 ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! ! line con 0 line vty 0 4 login local ! end
Here are the two problems I am facing:
1. Clients can associate to the wireless network (I see the message on the command line of the AP) but cannot get an IP addres by DHCP
2. When I set up an IP address manually (eg. 192.168.0.5/25, GW: 192.168.0.1, DNS: 192.168.0.1) on a computer connected to the wireless network, I can only ping the AP.
From the command line of the AP I can succesfully ping all the network devices (router, switch, printers, etc) and also I can ping the computer connected via wireless with the IP manually set up.
Please take a look at the configuration and tell me what can I do.
Transferring Crash file from standby: Login to the Active WLC in HA.
From CLI: (Cisco Controller) >transfer upload datatype crash (Cisco
Controller) >transfer upload filename (Cisco
Controller) >transfer upload mode tftp (Cisco Controller) >transfer
This is the start of a display filter cross reference between Wireshark
and OmniPeek. The 1st installment is a table of advanced filters. More
filters will be added as time allows. It is a living doc, so check back
for changes every so often Please feel f...