Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

AP HREAP NOT WORKING - NO DHCP, NO INTERNET ACCESS

Current Setup

WLC  > WAN < AP

AP is in HREAP mode

The Wireless SSID shows up at the remote site

Clients can associate to the SSID on the AP (HREAP)

But it's not handing out DHCP address

From the AP (HREAP mode) I cannot ping the WLC (connected via WAN link)

From the AP (HREAP mode) I cannot ping any network on the remote site.

I can access the WLC remotely.

From the WLC i can ping default gateway for the AP dhcp server

From the WLC i cannot ping the AP

On the WLC i cannot see any AP

---

AP2-1262#show capwap reap association

SSID: WirelessWLAN on Dot11Radio1

bssid: f4ea.67c1.618e  Mode: 0x192, WLAN: 2 , VLAN name: 002   VLAN ID: 66

Key Mgmt 12, Reap flags 0x1, Guest Yes, Current Users 0, Open Auth

SSID: WirelessWLAN on Dot11Radio0

bssid: f4ea.67c1.6181  Mode: 0x192, WLAN: 2 , VLAN name: 002   VLAN ID: 66

Key Mgmt 12, Reap flags 0x1, Guest Yes, Current Users 0, Open Auth

----------

Please HELP

Thanks!

5 REPLIES
Hall of Fame Super Silver

Re: AP HREAP NOT WORKING - NO DHCP, NO INTERNET ACCESS

First off, makes sure the h-reap ap is connected to a trunk port. The native vlan on the trunk port should be the vlan the ap management is on. Now on the WLAN SSID, make sure local switching is enabled in the advanced tab. Go to the h-reap ap and there is a tab on the top that says either h-reap or FlexConnect. Enter the native vlan and hit apply. Go back to that page and click on vlan mapping. Now set your WLAN SSID to the vlan out at the remote site you want to put traffic on.

If you want traffic to come back to the wlc, then you do not need to enable local switching in the WLAN said advanced tab. Your traffic will be tunneled back to the wlc and placed on the interface you chooses in the WLAN general page.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

AP HREAP NOT WORKING - NO DHCP, NO INTERNET ACCESS

Scott:

Thanks for your response.

I did trunk port the h-reap AP is connected to, however the native vlan is on the same vlan the AP is connected to not the AP management interface.  I will try what you suggested.

Local switching is enabled also.

Thank you.

Hall of Fame Super Silver

Re: AP HREAP NOT WORKING - NO DHCP, NO INTERNET ACCESS

you need to make sure the ap management vlan is the native vlan on the trunkport. You also need to make sure you configure you vlan mappings.

Sent from Cisco Technical Support iPad App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: AP HREAP NOT WORKING - NO DHCP, NO INTERNET ACCESS

If this doesn't answer your question, be more specific on where you want the traffic to go. Make sure you have dhcp setup right, routing is working, etc.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Gold

AP HREAP NOT WORKING - NO DHCP, NO INTERNET ACCESS

Duplicate posts. 

694
Views
5
Helpful
5
Replies
CreatePlease to create content