Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

AP received RESET from WLC

Dear All,

I am getting logs in the WLC (WiSM-1 running 7.0.235.0) as "AP Disassociated. Base Radio MAC:<radio mac>". Several of the APs have the same issue.

I telnet into one of the APs and collected the event logs and found below message,

"*** Access point reloading. Reason: Recvd RESET req from Controller ***". Before this message, I could see the Dot11Radio1 resetting continuously.

Attaching the event log file.

This is causing problems for the clients. Any suggestions/ideas would be of great help.

regards,

Girish

9 REPLIES
VIP Purple

AP received RESET from WLC

HI girish,

Can you paste the output from controller for this command:

sh sysinfo

Regards

New Member

AP received RESET from WLC

Here you go, same is for the other controller inside wism-1 blade.

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.235.0

RTOS Version..................................... 7.0.235.0

Bootloader Version............................... 7.0.235.0

Emergency Image Version.......................... 7.0.235.0

Build Type....................................... DATA + WPS

System Name...................................... WLC01

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.4

IP Address....................................... 10.0.x.x

System Up Time................................... 387 days 13 hrs 45 mins 14 secs

System Timezone Location.........................

Configured Country............................... GB  - United Kingdom

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +39 C

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 12

Number of Active Clients......................... 1402

Burned-in MAC Address............................ 64:00:F1:7F:8B:60

Maximum number of APs supported.................. 150

VIP Purple

AP received RESET from WLC

HI Girish,

Upgrade the software to 15.2(4)JB3 and see if we are able to reproduce the issue. i am pretty sure that this will resolve the issue!!

Check this doc:

http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/15.2_2_JB.pdf

Cisco IOS Release 15.2(2)JB does not support the following Cisco Aironet access points:

• AP 1130

• AP 1240

• AP 1250

• AP 1310

Change the IOS and then try again.

Regards

Dont forget to rate helpful posts

VIP Purple

AP received RESET from WLC

HI Girish,

download new image from here:

http://software.cisco.com/download/release.html?mdfid=281235915&flowid=6779&softwareid=280775090&release=15.2.4-JB3&relind=AVAILABLE&rellifecycle=ED&reltype=latest

Regards

Dont forget to rate helpful posts and mark this question as answered, it may help others.

New Member

AP received RESET from WLC

Hi Sandeep,

We are running wism-1 with 7.0.235.0 image. APs are controlled by the Wism. If I change the recovery image in the 1250 ap, will it associate itself with the WLC? Please note that the wism-1 cannot be upgraded beyond 7.0.240.0.

Please advice.

regards,

girish

VIP Purple

Re: AP received RESET from WLC

HI Girish,

Yes it will.

1250 AP supports 7.0.235.0 /  7.0.240.0.

http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html

If you face any troubles while joing AP to WLC, u can feel free to ask.

Regards

Dont forget to rate helpful posts

New Member

AP received RESET from WLC

Hi Sandeep,

We will have to plan WLC upgrade to newer code. Will post the results once it is done.

regards,

Hall of Fame Super Silver

Re: AP received RESET from WLC

Have you had to replace any of these 1252's? I have seen in the last few years these have been problematic with failing. One thing is that once you download the event log, make sure you delete and event logs and crash files on flash. I would also keep track of what AP's this is happening to and see if it's an issue with the same AP's or not. As long as nothing has changed in the environment, I would start tracking AP's with issues and maybe replace those.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: AP received RESET from WLC

The recovery image is only used when there is no other lightweight images on the AP. It will not just use that image unless you delete all other image file or you set the AP to boot from that image. It really doesn't matter what version of RCV image you use since the AP will download the image bundle from the WiSM.

You might be safe also to open a TAC case to see if they have any additional info.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
168
Views
0
Helpful
9
Replies
CreatePlease to create content