Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

AP1262N AN Radio configuration (autonomous)

Recently installed a 1262N AP in autonomous mode. Have both 2.4 and 5Ghz radios running- Both on separate SSID and VLAN.  I think I have 5Ghz channels using 40Mhz bands (bonded) but when I do iperf throughput test I only get about 25Mb throughput. I am sitting within 10 feet of the AP. When I switch to 2.4 I get around 60Mb and that's not bonded. I have tried multiple interfaces on my client side laptop I'm testing with since I thought maybe it was a quirky card or driver but I get same results. Am I doing something wrong here?  My laptop shows a 300Mb connection to 5Ghz and 144Mb on 2.4Ghz but I know that's not true thorughput so that's why I was testing this to see what I was really getting and now I'm confused.

Thanks!

Everyone's tags (4)
4 REPLIES
Hall of Fame Super Gold

AP1262N AN Radio configuration (autonomous)

I think I have 5Ghz channels using 40Mhz bands (bonded) but when I do iperf throughput test I only get about 25Mb throughput. I am sitting within 10 feet of the AP.

Stupid question from me:  Do you have all SIX antennas attached?  If you do, please specify what models you are are using.

New Member

AP1262N AN Radio configuration (autonomous)

Yes 3 2.2 Dbi 2.4Ghz antennas and 3 3.5 Dbi 5Ghz ones. Part Numbers. AIR-ANT2422DW and AIR-ANT5135DW.

Hall of Fame Super Gold

AP1262N AN Radio configuration (autonomous)

Ok, on the autonomous WAP, run the command "sh dot11 ass " and on the client side, what is the signal strength.

Back to the WAP, please run the following command:

dot11 dot111 carrier busy

dot11 dot110 carrier busy

Do the "sh log" and please post the output or result.

New Member

AP1262N AN Radio configuration (autonomous)

OK commands are a little off but I think I got what you asked for. Highlighted is the laptop I'm on.

mfrey-cisapupstairs#sho dot11 statistics client-traffic interface dot11Radio 1                    

Dot11Radio1: -- Client Statistics

---Clients     AID VLAN     Status   Age Tx   Mode Enc Key      Rate

0021.6a98.b068   2 3193 00 140 000 0FE 20   1-1 7F80 200 0-10 00FFFFFF 40E 80F

70de.e22b.1e3b   1 3193 00 160 000 0FE 26   0-0 3180 200 0-10 00FFFF00 107 107

                 RxPkts KBytes Dup Dec Mic   TxPkts KBytes Retry RSSI SNR

0021.6a98.b068   21729   2718   4   0   0   12250   5392   2837   64 27

70de.e22b.1e3b   13120   507 305   0   0     1165     232   603   66 26

               IP Address     Pauses   RSC

0021.6a98.b068 10.31.93.100   00000 [0]0x2E29

70de.e22b.1e3b 10.31.93.103   00000 [0]0x2D1

   Block Ack Pri, Rcv Wind Timeout SeqNum Held, Xmt Wind Timeout

0021.6a98.b068   0       64     5000   E2A0   0       64       31 0, 0 0 0

70de.e22b.1e3b   0       64       0   C1A0   0         8       0 0, 0 0 0

Video Report: Cnt Rate Retries/Tot

8021x auth in prog -23 allowed 0

mfrey-cisapupstairs#sho dot11 carrier busy

Frequency  Carrier Busy %

---------  --------------

   5180          0

   5200          1

   5220          2

   5240          1

   5260          1

   5280          0

   5300          2

   5320          0

   5500          2

   5520          1

   5540          0

   5560          0

   5580          0

   5660          0

   5680          0

   5700          0

   5745          0

   5765          1

   5785          2

   5805          0

   5825          1

Frequency  Carrier Busy %

---------  --------------

   2412         14

   2417          6

   2422          2

   2427          0

   2432          2

   2437          7

   2442          4

   2447          5

   2452          2

   2457          8

   2462         15

978
Views
0
Helpful
4
Replies